| |
|
23 |
FLUID SYSTEMS AND COMPONENTS FOR GENERAL USE |
| 23.020 |
Fluid storage devices |
| MS 1241 : 1991 | |
| Specification for fibreglass water tanks - Effective capacity of less than 2000 litres. | |
| This specification applies to tanks subjected only to hydrostatic head of water and intended for storage of potable water, in systems connected to public mains. Tanks shall be used indoor. The tanks are designed for domestic and commercial use only. Nominal capacity of tanks shall be less than 2000 litres.This specification only covers the use of polyester resin in wet lay-up system, excluding sectional panel and cast-in-situ tanks. The tank has to be gelcoated and protected from ultraviolet light by ultraviolet stabilizers. | |
| Price Code : C | |
| 23.020.30 |
Pressure vessels, gas cylinders |
| MS 1464 : 1999 | |
| Vocabulary on gas cylinder | |
| Establishes the terminology used in the field of gas cylinders. It also gives definitions relating to pressures and gases in Appendix A and Appendix B respectively. This standard is technically equivalent to ISO 10286 : 1992. | |
| Price Code : B | |
| MS 1512 : 2001 | |
| Cylinders for dissolved acetylene - Periodic inspection and maintenance | |
| Specifies the minimum requirements for periodic inspection and maintenance to verify the integrity of acetylene cylinders for further service, regardless of the method of manufacture of the shell. It does not exclude the application of additional national requirements. | |
| Price Code : C | |
| MS ISO 3807 : 1998 | |
| Dissolved acetylene cylinders - Basic requirements. | |
| This Malaysian Standard is identical with ISO 3807 : 1977. The standard specifies the basic requirements for dissolved acetylene cylinders with a maximum nominal water capacity of 160 l, the procedure for type testing and the method for determining the porosity of the porous mass. It does not include details of design for the cylinder shell as these are specified in other ISO standards such as ISO 4705 or ISO 4706. | |
| Price Code : A | |
| 23.040 |
Pipeline components and pipelines |
| 23.040.01 |
Pipeline components and pipelines in general |
| MS 1063 : 2002 | |
| Plastics piping systems for soil, ventilation and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U): Part 1: Specifications for pipes, fittings and the system (First revision). | |
| This Malaysian Standard specifies the requirements for pipes, fittings and the system of unplasticized poly (vinyl chloride) (PVC - U) piping systems in the field of soil, ventilation and waste discharge (low and high temperature) inside buildings (marked with “B”), for soil and waste discharge systems buried in ground within the building structure (marked with “D”) and for soil, ventilation and waste discharge for both inside buildings and buried in building structures (marked with “BD”). It also specifies the test parameters for the test method referred to in this standard. This standards supersedes MS 1063: 1986. | |
| Price Code : E | |
| 23.040.10 |
Iron and steel pipes |
| MS 636 : 1984 | |
| Specification for malleable cast iron screwed pipe fittings for steam, air, water, gas and oil. | |
| Covers materials, tests and dimensions of plain and reinforced fittings suitable for working pressures up to 1.380 MN/m squared for water and 1.035 MN/m squared for steam, air, gas and oil. | |
| Price Code : D | |
| MS 709 : 1981 | |
| Specification for cast iron non-pressure pipes and fittings. | |
| Covers requirements, definitions and test methods for pipe and fittings of nominal diameters up to 150 mm manufactured by sand cast or spun process, with type a or type B sockets. Designed for use above ground, for soil waste, ventilating and rain water, and any other purpose where the internal pressure is negligible. | |
| Price Code : D | |
| MS 862 : 1983 | |
| Specification for welded and seamless carbon steel pipes for general pressure purposes. | |
| Specifies dimensions, materials, various mechanical strength and other requirements for pipes of nominal bores in the range 6 mm -120 mm. Excludes pipe for boilers, oil, natural gas and other similar installations. | |
| Price Code : C | |
| MS 863 : 1983 | |
| Specification for welded and seamless steel pipes (6 mm to 150 mm) screwed-type. | |
| Specifies dimensions, materials, type of finish and various mechanical strength requirements for pipes of nominal bores 6 mm to 150 mm with ends either screwed and socketed or plain-ended. | |
| Price Code : B | |
| 23.040.20 |
Plastics pipes |
| MS 628 : Part 1 : 1999 | |
| Specification for unplasticised PVC (uPVC) pipes for water supply : Part 1 : Pipes (First revision) | |
| Specifies the requirements for unplasticised PVC pipes for pressure application for use in cold water services or potable water. The pressure rating of the pipes shall be of PN 9, PN 12 or PN 15 or unless specified otherwise. The pipes shall be supplied in standard 6 m lengths with an integral socket formed on one end to provide for jointing by mechanical rubber ring or solvent weld joints. The plain end shall be chamfered to facilitate insertion during jointing and witness mark shall be put at the spigot end of the pipe. Other lengths may be supplied as agreed upon between purchaser and supplier. The pipes shall conform to the standards as stated unless specifically specified otherwise. Rubber ring joints shall be manufactured for pipe sizes of 80 mm and above. For pipe sizes below 80 mm, the plain end or solvent weld joint pipes shall be manufactured. This standard supersedes MS 628 : 1982. | |
| Price Code : D  Amendment 2 : 2002 | |
| MS 628 : Part 2 : Section 2.1 : 1999 | |
| Specification for unplasticised pvc (uPVC) pipes for water supply : Part 2 : Joints and fittings for use with unplasticised pvc pipes : Section 2.1 : uPVC joints and fittings | |
| Specifies the requirements for unplasticised PVC joints and fittings made principally of unplasticised polyvinyl chloride and of which one or more of the joints are intended for unplasticised PVC pressure pipes complying with MS 628 : Part 1. Joints complying with the standard may be either purpose made socket formed on the pipe complying with MS 628 : Part 1, or detachable couplers and other fittings, which are injection, moulded. This Malaysian Standard supersedes MS 923 : Part 1 : 1984, Specification for unplasticised PVC pipe for pressure pipe : Part 1 : Injection moulded unplasticised PVC fitting for solvent welding for use with pressure pipe, including potable water supply and MS 923 : Part 3 : 1989, Specification for unplasticised PVC pipe for pressure pipe : Part 3 : Mechanical joint & fitting principally of unplasticised PVC. | |
| Price Code : D | |
| MS 628 : Part 2 : Section 2.2 : 1999 | |
| Specification for unplasticised pvc (uPVC) pipes for water supply : Part 2 : Joints and fittings for use with unplasticised PVC pipes : Section 2.2 : Solvent cement | |
| Specifies the requirements for solvent cement, supplied in cans or tubes for jointing unplasticised PVC pressure pipes complying with the requirements of MS 628 : Part 1 and MS 762, unplasticised PVC fittings complying with the requirements of BS 4346 : Part 1 and unplasticised PVC pipes and fittings complying with the requirements of BS 5481. The solvent cement is also suitable, along with solvent cement complying with the requirements of BS 6209, for jointing products complying with the requirements of BS 4514, BS 4576 : Part 1 and BS 4660. This standard supersedes MS 923 : Part 2 : 1984, Specification for joints and fittings for use with unplasticised PVC pressure pipes : Part 2 : Solvent cement. | |
| Price Code : B | |
| MS 628 : Part 3 : 1999 | |
| Specification for unplasticised pvc (upvc) pipes for water supply : Part 3 : Guide for installation | |
| Sets out recommended method of handling and installing unplasticised PVC pipes for water supply. | |
| Price Code : C | |
| MS 762 : 1982 | |
| Specification for unplasticized PVC pipe for industrial use. | |
| Specifies materials to be used, classification of pipes, physical and mechanical properties. Includes test methods for sampling, marking and storage of pipes. | |
| Price Code : B | |
| MS 978 : 1985 | |
| Specification for plastics waste pipe and fittings. | |
| Covers plastic materials as stated : (a) acrylonitrile-butadiene-styrene (ABS) (b) modified unplasticised polyvinyl chloride (MUPVC) (c) polypropylene (PP) (d) polyethylene (PE) intended to convey normal domestic effluent. | |
| Price Code : D | |
| MS 979 : Part 1 : 1985 | |
| Specification for unplasticizes sewerage pipes and fittings : Part 1 : Pipes of diameter 100 millimeter and 155 millimeter. | |
| Specifies material, colour, dimensions and testing of products for the conveyance of normal domestic effluents and surface water. Applies to product laid under gardens, fields, driveway, yards and roads other than main roads. | |
| Price Code : C | |
| MS 979 : Part 2 : 1985 | |
| Specification for unplasticized PVC underground sewerage pipes and fittings : Part 2 : Pipes of diameter 200 millimetres and above. | |
| As in Part 1 of this standard but for diameters ranging from 200 mm to 630 mm. | |
| Price Code : C | |
| MS 1035 : 1986 | |
| Code of practice for unplasticized PVC pipework for the conveyance of liquid under pressure. | |
| Gives guidance on the proper application and installation of UPVC (unplasticized polyvinyl chloride) pipes for the conveyance of liquid under pressure. | |
| Price Code : C | |
| MS 1058 : Part 1 : 2002 | |
| Specification for polyethylene (PE) Piping systems for water supply ): Part 1 : General (Third revision). | |
| This Part of
Malaysian Standard specifies the general aspects of
polyethylene (PE) piping systems in the field of water
supply intended for human consumption including the
conveyance of raw water prior to treatment. It also
specifies the test parameters for the test methods
referred to in this standard. In conjunction with other
Parts of MS 1058, it is applicable to PE pipes, fittings,
their joints and to joints with components of
non-plastics 2001materials intended to be used under the
following conditions: a) buried water mains and service pipes; b) a maximum operating pressure, MOP, up to and including 16 bar; c) an operating temperature of 20 °C as reference temperature This standard supersedes MS 1058 : Part 1 : 1998. |
|
| Price Code : B | |
| MS 1058 : Part 2 : 2002 | |
| Specification for polyethylene (PE) Piping systems for water supply ): Part 2: Pipes (Third revision). | |
| This Part of
Malaysian Standard specifies the general aspects of
polyethylene (PE) piping systems in the field of water
supply intended for human consumption including the
conveyance of raw water prior to treatment. It also
specifies the test parameters for the test methods
referred to in this standard. In conjunction with other
Parts of MS 1058, it is applicable to PE pipes, their
joints and to joints with components of PE and
non-plastics materials intended to be used under the
following conditions: a) buried water mains and service pipes; b) a maximum operating pressure, MOP, up to and including 16 bar; and c) an operating temperature of 20 °C as reference temperature This standard supersedes MS 1058 : Part 1 : 1998. |
|
| Price Code : B | |
| MS 1419 : Part 4 : 1998 | |
| Specification for acrylonitrile butadiene styrene (ABS) pipes and fittings for pressure applications : Part 4 : Installation of ABS pipe system. | |
| This Malaysian Standard specifies requirements and sets out recommended methods for installing acrylonitrile butadiene styrene (ABS) pipeline, above or below ground, for both pressure and non-pressure applications. Information is included on the selection, storage and handling, of ABS pipes. | |
| Price Code : E | |
| MS ISO 265-1 : 2003 | |
| Pipes and fittings of plastics materials – Fittings for domestic and industrial waste pipes – Basic dimensions: Metric series – Part 1: Unplasticized poly(vinyl chloride) (PVC-U). | |
| This Malaysian Standard is identical with ISO 265-1:1988. This Malaysian Standard specifies the series of diameters and the formulae for calculation of the dimensions common to the main types of fittings with spigot ends, socket fittings and socket fittings with curved (swept) entries of unplasticized poly(vinyl chloride) (PVC-U) for domestic and industrial waste pipes, regardless of the method of manufacture (with the exception of fittings fabricated from pipes) and of the composition. | |
| Price Code : C | |
| MS ISO 580 : 2003 | |
| Injection-moulded unplasticized poly(vinyl chloride) (PVC-U) fittings – Oven test – Test method and basic specifications. | |
| This Malaysian Standard is identical with ISO 580:199. This Malaysian Standard specifies a method to establish the quality of injection-moulded unplasticized poly(vinyl chloride) (PVC -U) fittings using an oven. It applies both to pressure fittings and to non-pressure fittings used for drainage applications, as well as to flanged fittings and fittings incorporating elastomeric sealing rings and to fittings consisting of the assembly of a number of moulded parts. | |
| Price Code : A | |
| MS ISO 2505-1 : 2002 | |
| Thermoplastics pipes – Longitudinal reversion – Part 1: Determination methods. | |
| This part of MS ISO 2505 specifies two methods for determining the longitudinal reversion of thermoplastics pipes, to be carried out in liquid (method A) or in air (method B). In case of disagreement, method A is to be used as the reference method. | |
| Price Code : A | |
| MS ISO 2505-2 : 2002 | |
| Thermoplastics pipes – Longitudinal reversion – Part 2: Determination parameters. | |
| This part of MS ISO 2505 specifies the parameters for the determination of the longitudinal reversion of thermoplastics pipes in accordance with methods A and B specified in MS ISO 2505–1, i.e. using a liquid bath or an air oven. | |
| Price Code : A | |
| MS ISO 2507-1 : 2002 | |
| Thermoplastics pipes and fittings – Vicat softening temperature – Part 1: General test method. | |
| This part of MS ISO 2507 specifies a general method for determining the Vicat softening temperature of thermoplastics pipes and fitting. It includes the adaptation of method B of ISO 306: 1994, using a force of 50 N. | |
| Price Code : A | |
| MS ISO 2507-2 : 2002 | |
| Thermoplastics pipes and fittings – Vicat softening temperature – Part 2: Test conditions for unplasticized poly (vinyl chloride) (PVC–U) or chlorinated poly (vinyl chloride) (PVC–C) pipes and fittings and for high impact resistance poly(vinyl chloride) (PVC–HI) pipes. | |
| This part of MS ISO 2057 specifies the particular test conditions for determining the Vicat softening temperature (VST) of unplasticized poly (vinyl chloride) (PVC-U) or chlorinated poly (vinyl chloride) (PVC-C) pipes and fittings and of high impact resistance poly (vinyl chloride) (PVC-H) pipes. | |
| Price Code : A | |
| MS ISO 3127 : 2002 | |
| Thermoplastics pipes – Determination of resistance to external blows – Round–the–clock method. | |
| This Malaysian Standard specifies a method for the determination of the resistance to external blows of thermoplastics pipes of circular cross-section; it is called the round–the–clock method. | |
| Price Code : B | |
| MS ISO 4065 : 2003 | |
| Thermoplastics pipes – Universal wall thickness table. | |
| This Malaysian Standard is identical with ISO 4065:1996. This Malaysian Standard specifies the relationship between the nominal wall thickness and the nominal outside diameter of thermoplastics pipes. It is applicable to smooth thermoplastics pipes of constant circular cross-section along with the whole length of the pipe, whatever their method of manufacture, their composition or their intended application. | |
| Price Code : B | |
| MS ISO 9080 : 2004 | |
| Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation | |
| This standard describes a method for estimating the long-term hydrostatic strength of thermoplastics materials by statistical extrapolation. | |
| Price RM30 | |
| MS ISO 9852 : 2002 | |
| Unplasticized poly(vinyl chloride) (PVC-U) pipes - Dichloromethane resistance at specified temperature (DCMT) – Test method. | |
| This Malaysian Standard specifies a method for determining the resistance of unplasticized PVC pipes to dichloromethane at a specified temperature (DCMT). | |
| Price Code : A | |
| MS ISO 9853 : 2003 | |
| Injection-moulded unplasticized poly(vinyl chloride) (PVC-U) fittings for pressure pipe systems – Crushing test | |
| This Malaysian Standard is identical with ISO 9853:1991. This Malaysian Standard specifies a crushing test to determine the percentage deformation of injection-moulded unplasticized poly(vinyl chloride) (PVC-U) fittings and recommends a baics specification. It applies to injection-moulded PVC-U fittings for pressure pipelines, fittings with solvent sockets and fittings with sockets with elastomeric sealing rings. | |
| Price Code : A | |
| MS ISO 11173 : 2002 | |
| Thermoplastics pipes – Determination of resistance to external blows – Staircase method. | |
| This Malaysian Standard specifies a method for determining the resistance to external blows of thermoplastics pipes of circular cross – section; it is called the staircase method. | |
| Price Code : A | |
| MS ISO 11922-1 : 2003 | |
| Thermoplastics pipes for the conveyance of fluids – Dimensions and tolerances – Part 1: Metric series. | |
| This Malaysian Standard is identical with ISO 11922-1:1997. This Malaysian Standard specifies tolerance grades for the outside diameter, out-of-roundness and wall thickness of metric thermoplastics pipes for the conveyance of fluids and manufacture with nominal outside diameters and nominal pressure. It is applicable to smooth thermoplastics pipes of constant circular cross-section along the whole length of the pipe, whatever the method of manufacture, the pipe material or the intended application. | |
| Price Code : B | |
| MS ISO 11922-2 : 2003 | |
| Thermoplastics pipes for the conveyance of fluids – Dimensions and tolerances – Part 2: Inch-based series. | |
| This Malaysian Standard is identical with ISO 11922-2:1997. This Malaysian Standard specifies tolerance grades for the outside diameter, out-of-roundness and wall thickness of inch-based thermoplastics pipes for the conveyance of fluids and manufacture with nominal outside diameters and nominal pressure. It is applicable to smooth thermoplastics pipes of constant circular cross-section along the whole length of the pipe, whatever the method of manufacture, the pipe material or the intended application. | |
| Price Code : B | |
| MS ISO 12162 : 2003 | |
| Thermoplastics materials for pipes and fittings for pressure applications – Classification and designation – Overall service (design) coefficient. | |
| This Malaysian Standard is identical with ISO 12162:1995. This Malaysian Standard establishes the classification of thermoplastics materials in pipe form and specifies the material designation. It also gives a method for calculating the design stress. It applies to materials intended for pipes and/or fittings for pressure applications. The classification, the material designation, and the calculation method are based on the resistance to internal pressure with water at 20 ºC in water for 50 years, derived by extrapolation using the method given in ISO/TR 9080. | |
| Price Code : A | |
| MS ISO 13760 : 2004 | |
| Plastic pipes for the conveyance of fluids under pressure - Miner's rule- Calculation method for cumulative damage. | |
| This standard specifies a method for calculating the maximum allowable hoop stress applicable to pipes exposed to varying internal pressure and/or temperatures during their expected lifetime. | |
| Price Code : A | |
| 23.040.40 |
Metal fittings |
| MS 708 : 1981 | |
| Specification for grey iron pipes and fittings. | |
| Covers requirements and test methods for : 1. Pipes manufactured by the following processes: i. Centrifugal casting in metal moulds ii. Centrifugal casting in sound moulds iii. Casting in sand moulds 2. Fittings. | |
| Price Code : E | |
| MS 1094 : 1987 | |
| Specification for cast iron fittings for asbestos cement pressure pipe. | |
| Specifies cast ion fittings or asbestos cement pressure pipes conforming to MS 712. The requirements specified are material, workmanship, dimensional and hydrostatic performance tests. | |
| Price Code : B | |
| 23.040.45 |
Plastics fittings |
| MS ISO 727 : 1997 | |
| Fittings of unplasticised polyvinyl chloride (PVC -U), chlorinated polyvinyl chloride (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure - Dimensions of sockets - Metric series. | |
| This
Malaysian Standard is a total adoption of ISO Standard
727 : 1985. This standard specifies the dimension of
plain sockets on fittings made from unplasticised
polyvinyl chloride (PVC-U), chlorinated polyvinyl
chloride (PVC-C) or acrylonitrile butadiene styrene
(ABS), intended for connecting by solvent cementing to
pipes of the corresponding material for use under
pressure. |
|
| Price Code : A | |
| MS 1010 : 1986 | |
| Specification for rigid polyvinyl chloride and related plastic pipe and fitting compounds. | |
| This
Malaysian Standard specifies the physical requirements
and test methods for the rigid vinyl chloride compounds
for pipes and fittings. The compounding ingredients may
consist of lubricants, stabilizers, (vinyl chloride)
resin modifiers, pigments and inorganic fillers. |
|
| Price Code : C | |
| MS 1419 : Pt. 1 : 1997 | |
| Specification for acrylonitrile butadiene styrene (ABS) pipes and fittings for pressure applications : Part 1: Pipes | |
| This
Malaysian Standard specifies the requirements for pipes
up to 200mm nominal size manufactured from acrylonitrile
butadiene styrene (ABS) polymer for pressure applications
for conveyance of potable water and other liquids and
gases. Pipes manufactured in accordance with this
standard are not intended for the transport gaseous
fuels. |
|
| Price Code : D | |
| MS 1419 : Pt. 2 : 1997 | |
| Specification for acrylonitrile butadiene styrene (ABS) pipes and fittings for pressure applications : Part 2 : Solvent cement fittings. | |
| The
Malaysian Standard specifies the requirements for the
moulded acrylonitrile butadiene styrene (ABS) fittings
for solvent cement jointing to ABS pipes up to 200 mm
nominal size complying with MS 1419: Pt. 1:1997 |
|
| Price Code : C | |
| MS 1419 : Pt. 3 : 1997 | |
| Specification for acrylonitrile butadiene styrene (ABS) pipes and fittings for pressure applications : Part 3 : Solvent cement and priming (cleansing) fluids for use with ABS pipes and fittings. | |
| The
Malaysian Standard specifies the requirements for solvent
cement and priming (cleaning) fluids used in the jointing
of acrylonitrile butadiene styerene( ABS) pipes and
fittings and in the fabrication of ABS fittings. |
|
| Price Code : C | |
| MS 1419 : Part 4 : 1998 | |
| Specification for acrylonitrile butadiene styrene (ABS) pipes and fittings for pressure applications : Part 4 : Installation of ABS pipe system. | |
| This
Malaysian Standard specifies requirements and sets out
recommended methods for installing above or below ground,
for both pressure and non-pressure applications.
Information is included on the selection, storage and
handling, of ABS pipes. |
|
| Price Code : E | |
| MS ISO 2507-1 : 2002 | |
| Thermoplastics pipes and fittings – Vicat softening temperature – Part 1: General test method. | |
| This part of MS ISO 2507 specifies a general method for determining the Vicat softening temperature of thermoplastics pipes and fitting. It includes the adaptation of method B of ISO 306: 1994, using a force of 50 N. | |
| Price Code : A | |
| MS ISO 2507-2 : 2002 | |
| Thermoplastics pipes and fittings – Vicat softening temperature – Part 2: Test conditions for unplasticized poly (vinyl chloride) (PVC–U) or chlorinated poly (vinyl chloride) (PVC–C) pipes and fittings and for high impact resistance poly(vinyl chloride) (PVC–HI) pipes. | |
| This part of MS ISO 2057 specifies the particular test conditions for determining the Vicat softening temperature (VST) of unplasticized poly (vinyl chloride) (PVC-U) or chlorinated poly (vinyl chloride) (PVC-C) pipes and fittings and of high impact resistance poly (vinyl chloride) (PVC-H) pipes. | |
| Price Code : A | |
| MS ISO 12162 : 2003 | |
| Thermoplastics materials for pipes and fittings for pressure applications – Classification and designation – Overall service (design) coefficient. | |
| This Malaysian Standard is identical with ISO 12162:1995. This Malaysian Standard establishes the classification of thermoplastics materials in pipe form and specifies the material designation. It also gives a method for calculating the design stress. It applies to materials intended for pipes and/or fittings for pressure applications. The classification, the material designation, and the calculation method are based on the resistance to internal pressure with water at 20 ºC in water for 50 years, derived by extrapolation using the method given in ISO/TR 9080. | |
| Price Code : A | |
Pipes and fittings of other materials |
|
| MS 712 : 1991 | |
| Specification for asbestos - Cement pressure pipes (First revision). | |
| This
standard applies to asbestos-cement pipes and joints
(collars) for use under pressure. It covers four types of
pipes, characteristically for use with different working
heads of water. The pipes may be steam cured or water
cured. |
|
| Price Code : B | |
| MS 1059 : 1986 | |
| Specification for asbestos-cement sewer pipes joints and fittings. | |
| Applies to
asbestos cement pipes, joints and fittings for use with
gravity flow at atmospheric pressure and intended for
sewerage and drainage applications. It covers three
classes of pipes for use in different trench loading
conditions. |
|
| Price Code : B | |
Hoses and hose assemblies |
|
| MS ISO 2398 : 2002 | |
| Rubber hose, textile-reinforced, for compressed air - Specification | |
| This Malaysian Standard specifies the requirements for seven types and two classes of rubber hose for compressed air up to a maximum working pressure of 2,5 Mpa and a hose operating-temperature range of between -40 °C and + 70 °C, depending on the class. | |
| Price Code : A | |
| MS ISO 6804 : 2002 | |
| Rubber hoses and hose assemblies for washing-machines and dishwashers - Specification for inlet hoses | |
| This Malaysian Standard specifies requirements for inlet rubber hoses and hose assemblies for washing-machines and dishwashers connected to the domestic water supply at a pressure not exceeding 1 MPa (10bar). | |
| Price Code : A | |
| MS ISO 8330 : 2002 | |
| Rubber and plastics hoses and hose assemblies - Vocabulary | |
| This Malaysian Standard defines terms used in the hose industry. The terms are listed alphabetically in English. | |
| Price Code : B | |
Seals for pipe and hose assemblies |
|
| MS 1292 : 1992 | |
| Specification for rubber seals-water stops for sealing joints in concrete - Specification of materials. | |
| This Malaysian Standard specifies requirements for materials used in vulcanized, solid rubber water stops for sealing joints in concrete into which they are wholly or partly embedded. Some general requirements for the finished water stops are also given. This Malaysian Standard is not applicable to flexible polyvinylchloride or cellular rubber water stops. | |
| Price Code : A | |
Valves |
|
| MS 831 : 1986 | |
| Specification for valves for use with domestic liquefied petroleum gas (LPG) cylinders. | |
| Requirements for valve material, dimensions, performance and safety features specified. | |
| Price Code : B | |
| MS 1022 : 1986 | |
| Specification for stopvalves for water services (Screwdown patterns). | |
| Specifies requirements for screwdown pattern stopvalves of nominal sizes ¼, 3/8, ½, ¾, 1, 1¼, 1½, and 2. | |
| Price Code : E | |
| MS 1049 : 1986 | |
| Specification for double flanged cast iron wedge gate (sluice) valves for waterworks purposes. | |
| Specifies requirements for double flanged inside screw, solid wedge ,metal or resilient seated, non-rising stem type cast iron wedge gate (sluice) valves for waterworks purposes, whether above or below ground. Valves in accordance with this specification are primarily intended for use with portable water and for operation by a removable key or a hand-wheel. | |
| Price Code : C | |
Valves in general |
|
| MS 1396 : 1996 | |
| Specification for ferrules. | |
| This
Malaysian Standard specifies the requirements for the
design, materials, manufacture and testing for: Type A - swivel ferules of ½" (15 mm), ¾" (20 mm), 1¼" (32 mm), 1½" (40 mm) and 2" (50 mm). Type B - vertical ferrules of ½" (15 mm), ¾" (20 mm) and 1" (25 mm). |
|
| Price Code : B | |
Pressure regulators |
|
| MS 1165 : 1989 | |
| Specification for pressure regulators and automatic changeover devices for liquefied petroleum gases. | |
| Specifies materials, constructions, performance and testing requirements of ions and high pressure regulators and automatic changeover devices with screwed and clipped on connectors for use with butane and propane vapour phase up to a maximum vapour pressure of 20 bar and a maximum of 20 kg of gas per hour where storage and operational temperatures are between -20½oC and 50½oC. Also covers connections, vent range of adjustment, pressure gauges and indicators, valves and sealing. | |
| Price Code : C | |
| MS 1720 : 2003 | |
| Welded carbon steel gas cylinders – Periodic inspection and testing | |
| This Malaysian Standard specifies the minimum requirements for periodic inspection and testing to verify the integrity of gas cylinders for further service. It does not exclude the application of additional national requirements. | |
| Price : RM40 | |
Check Valves |
|
| MS 1461 : 1999 | |
| Specification for draw off taps with metal bodies for water services | |
| Specifies the requirement for the design, materials, manufacture and testing of ½ inch and ¾ inch nominal size draw-off taps. This standard supersedes MS 929 : Part 1 : 1984, MS 929 : Part 2 : 1984, MS 929 : Part 3 : 1984, and MS 929 : Part 4 : 1984. | |
| Price Code : C | |
Pumps |
|
| MS IEC 60335-2-41 : 2003 | |
| Household and similar electrical appliances safety Part 2-41: Particular requirements for pumps | |
| This clause of Part 1 is replaced by the following. This Malaysian Standard deals with the safety of electric pumps for liquids having a temperature not exceeding 90 °C, intended for household and similar purposes, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. | |
| Price : RM20 | |
| MS IEC 60335-2-51 : 2003 | |
| Household and similar electrical appliances safety - Part 2-51: Particular requirements for stationary circulation pumps for heating and service water installations | |
| This clause of Part 1 is replaced by the following. This Malaysian Standard deals with the safety of electric stationary circulation pumps intended for use in heating systems or in service water systems, having a rated power input not exceeding- 300 W, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. | |
| Price : RM20 | |
Fluid power systems |
|
Cylinders |
|
| MS 217 : 1974 | |
| Method for the hydrostatic stretch testing of liquefiable and other compressed gas cylinders. | |
| Describes methods for hydrostatic strength testing of steel cylinders intended for storage and transport of liquefiable and other compressed gases. | |
| Price Code : B | |
| MS 641 : 1982 | |
| Specification for LPG cylinders up to 1000 pounds water capacity without electric-arc welded longitudinal seam. | |
| Covers type, size and service pressure, quality of steel, wall thickness and quality of manufacture. Sample of inspector's report and test methods provided. | |
| Price Code : B | |
| MS 642 : 1982 | |
| Specification for LPG cylinders up to 1000 pounds water capacity with electric-arc welded longitudinal seam. | |
| Same as MS 641 with addition of specification for street and analysis tolerances for the cylinders. | |
| Price Code : B | |
| MS 1474 : 1999 | |
| Cylinders for permanent gases - Inspection at time of filling | |
| Specifies minimum requirements for filling inspections of transportable gas cylinders for continued use. These requirements reflect current practice and experience. This standard applies to cylinders of water capacity from 0.5 l to 150 l for the transportation of permanent gases under pressure but does not deal with manifolded bundles or manifolded trailer cylinders, nor does it deal with inspecting or testing for internal contamination. | |
| Price Code : A | |
| MS 1475 : 1999 | |
| Cylinders for liquefied gases (excluding acetylene and LPG) - Inspection at time of filling | |
| Specifies the minimum requirements to verify the integrity of transportable gas cylinders for continued use. These requirements reflect current practice and experience. Standard applies to cylinders of water capacity from 0.5 l to 150 l for the transportation of liquefied gases (excluding acetylene and LPG) but does not apply to manifolded bundles or manifolded trailer cylinders; nor does it deal with inspecting or testing for internal contamination. | |
| Price Code : B | |
Ventilators. Fans. Air-conditioners |
|
| MS 1219 : Part 2 : 2002 | |
| Safety of household and similar electrical appliances Part 2 : Particular requirements for fans (First revision) | |
| This standard deals with the safety of electric fans for household and similar purposes individually installed and not belonging at a complex plants or components of machine, with a rated voltage not more than 250 V for single-phase and 480 V for the other appliances. This standard supersedes MS 1219 : 1992 | |
| Price Code : B | |
| MS 1220 : 2001 | |
| Performance and construction of electric circulating fans and regulators (First revision) | |
| This standard applies to the types of electric motor directly driven fans and their associated regulators intended for use on single-phase a.c. and d.c. circuits not exceeding 250V. This standard supersedes MS 1220 : 1992. | |
| Price Code : B | |
| MS IEC 60335-2-40 : 1999 | |
| Safety of household and similar electrical appliances : Part 2 : Particular requirements for electrical | |
| heat pumps, air-conditioners and dehumidifiersApplies to the safety of electric heat pumps, including sanitary hot water heat pumps, air-conditioners, and dehumidifiers incorporating sealed motor-compressors, their maximum rated voltages being not more than 250 V for single phase appliances and 600 V for all other appliances. This standard is identical with IEC 60335-2-40 : 1995. | |
| Price Code : E | |
| MS IEC 60335-2-65 : 1999 | |
| Safety of household and similar electrical appliances : Part 2 : Particular requirements for air-cleaning appliances (First revision) | |
| Deals with the safety of electrical air-cleaning appliances for household and similar purposes, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. This standard also applies to electrostatic air filters incorporated in other appliances. This standard is identical with IEC 60335-2-65 : 1993 and it supersedes MS IEC 335-2-65 : 1995. | |
| Price Code : B | |
| MS ISO 5151 : 2004 | |
| Non-ducted air conditioners and heat pumps – Testing and rating for perfomance | |
| This Malaysian Standard specifies the standard conditions on which the ratings of single-package and split-system non-ducted air conditioners employing air- and water-cooled condensers are based, and the test methods to be applied for determination of the various rating. | |
| Price : RM50 | |
| |
|