| |
|
| 75 |
PETROLEUM AND RELATED TECHNOLOGIES |
Extraction and processing of petroleum and natural gas |
|
| MS 790 : 1982 | |
| Method of test tor sediment in crude and fuel oils by extraction. | |
| Determines sediments in crude petroleum and fuel oils by extraction with tolerance. | |
| Price Code : A | |
Natural gas |
|
| MS 1204 : 2001 | |
| Code of practice for CNG compressor refuelling stations : On site storage and location of equipment (First revision) | |
| This code of
practice provides planning information, procedures,
standards and guidance, for the establishment of a CNG
compressor and refuelling station. The code specifies
requirements for pressure vessel design and construction,
location and installation of tanks, cylinders and
regulating equipment, pressure relief devices, CNG
transfer, pressure gauges, and vehicle refuelling
operation. This standard supersedes MS 1204 : 1991. |
|
| Price Code : D | |
| MS ISO 6326-1 : 1997 | |
| Natural gas - Determination of sulphur compounds- Part 1: General introduction | |
| This
Malaysian Standard is a total adoption of ISO
6326-1:1989. This standard provides a brief list of
standardised methods that can be used for the
determination of sulfur compounds in natural gas. The
principle of each method is described generally, the
concentration range for which the method is suited is
indicated and the sensitivity and precision of each
method is given. |
|
| Price Code : A | |
| MS ISO 6326-2 : 1997 | |
| Gas analysis - Determination of sulphur compounds in natural gas - Part 2: Gas chromatographic method using an electrochemical detector for the determination of odoriferous sulphur compounds. | |
| This Malaysian Standard is a total adoption of ISO 6326-2:1981. This standard specifies a gas chromatographic method for the qualitative and quantitative analysis of odoriferous sulfur compounds in natural gas. The method is applicable to the following compounds i.e. hydrogen sulphide, methanethiol and homologues up to butanethiols and thiacyclopentane. | |
| Price Code : A | |
| MS ISO 6326-3 : 1997 | |
| Natural gas - Determination of sulphur compounds - Part 3: Determination of hydrogen sulphide , mercaptan sulfur and carbonyl sulphide by potentiometry. | |
| This Malaysian Standard is a total adoption of ISO 6326-3:1989. This part of the specifies a potentiometric method for the determination of hydrogen sulfide, mercaptan sulfur, and carbonyl sulfide sulfur in natural gas in the concentration range equal to or above 1 mg/m3 | |
| Price Code : A | |
| MS ISO 6326-4 : 1997 | |
| Natural gas - Determination of sulphur compounds - Part 4: Gas chromatographic method using a flame photometric detector for the determination of hydrogen sulfide, carbonyl sulfide and sulfur containing odorants. | |
| This Malaysian Standard is a total adoption of ISO 6326-4:1994. This method is applicable to determination of hydrogen sulfide, carbonyl sulfide, C1 - C4 thiols and sulfides and tetrahydrothiophene (THT), generally in the range 0.5 m mol/mol to 50 m mol/mol. It is also applicable to the quantitative determination of sulfur compounds other than hydrogen sulfide, when hydrogen sulfide is present at concentrations up to 5000 m mol/mol. | |
| Price Code : B | |
| MS ISO 6326-5 : 1997 | |
| Natural gas - Determination of sulphur compounds - Part 4: Gas chromatographic method using a flame photometric detector for the determination of hydrogen sulfide, carbonyl sulfide and sulfur containing odorants. | |
| This
Malaysian Standard is a total adoption of ISO
6326-5:1989. This part of specifies a method for the
determination of total sulfur in natural gas. The method
is applicable to gases with sulfur contents between 0.5
mg/m3 and 1000 mg/m3. |
|
| Price Code : B | |
| MS ISO 6327 : 1996 | |
| Gas analysis - Determination of the water dew point of natural gas - Cooled surface condensation hygrometers. | |
| This
Malaysian Standard is a total adoption of ISO 6327 :
1981. This Malaysian Standard describes hygrometers used
for the determination of the water dew point of natural
gases by detecting water vapour condensation occurring on
a cooled surface or by checking the stability of the
condensation on this surface. |
|
| Price Code : A | |
| MS ISO 6568 : 1997 | |
| Natural gas - Simple analysis by gas chromatography. | |
| This
Malaysian Standard is a total adoption of ISO 6568:1981.
This standard specifies a method for the analysis of
natural gas containing less than 1% molar of hydrocarbons
containing more than 5 carbon atoms (generally called dry
natural gas), at any point from extraction up to the
distribution centre. It is applicable for the
determination of hydrocarbons having one to five carbon
atoms, carbon dioxide and nitrogen. |
|
| Price Code : A | |
| MS ISO 6570 : 2003 | |
| Natural gas - Determination of potential hydrocarbon liquid content - Gravimetric methods (First revision). | |
| This
Malaysian Standard is identical with ISO 6570:2001. This
Malaysian Standard describes the principles of, and
general requirements for, two gravimetric methods for the
determination of the potential hydrocarbon liquid content
of natural gas, or similar gas, at a given pressure and
temperature. This Malaysian Standard replaces MS ISO
6570-1:1996 and MS ISO 6570-2:1996. |
|
| Price Code : C | |
| MS ISO 6570-1 : 1996 | |
| Natural gas - Determination of potential hydrocarbon liquid content - Part 1 : Principles and general requirements | |
| This
Malaysian Standard is a total adoption of ISO 6570-1 :
1983. This part of the standard describes the principles
of, and general requirements for, methods for the
determination of the potential hydrocarbon liquid content
of natural gas, or similar gas, at a given pressure and
temperature. |
|
| Price Code : A | |
| MS ISO 6570-3 : 1996 | |
| Natural gas - Determination of potential hydrocarbon liquid content - Part 3 : Volumetric method | |
| This
Malaysian Standard is a total adoption of ISO 6570-3 :
1984. This part of the standard specifies a volumetric
method for the determination of the potential hydrocarbon
liquid content of natural gas. The method permits
simultaneous determination of the amount of water that
condense under the conditions of the test. |
|
| Price Code : B | |
| MS ISO 6974-1 : 2003 | |
| Natural gas - Determination of composition with defined uncertainty by gas chromatography - Part 1: Guidelines for tailored analysis (First revision) | |
| This Malaysian Standard is identical with ISO 6974-1:2000. This Malaysian Standard provides guidelines for the quantitative analysis of natural-gas-containing constituents. This Malaysian Standard replaces MS ISO 6974:1996. | |
| Price Code : C | |
| MS ISO 6974-2 : 2003 | |
| Natural gas - Determination of composition with defined uncertainty by gas chromatography - Part 2: Measuring-system characteristics and statistics for processing data (First revision) | |
| This Malaysian Standard is identical with ISO 6974-2:2001. This Malaysian Standard describes the data processing for the tailored analysis of natural gas. It includes determination of the measuring system characteristics and the statistical approach to data handling and error calculation with the aim of defining the uncertainty in the mole fractions of the component measured. This Malaysian Standard replaces MS ISO 6974:1996. | |
| Price Code : D | |
| MS ISO 6974-3 : 2003 | |
| Natural gas - Determination of composition with defined uncertainty by gas chromatography - Part 3: Determination of hydrogen, helium, oxygen, nitrogen, carbon dioxide and hydrocarbons up to C8 using two packed columns (First revision) | |
| This Malaysian Standard is identical to ISO 6974-3:2000. This Malaysian Standard describes a gas chromatographic method for the quantitative determination of the content of helium, hydrogen, oxygen, nitrogen, carbon dioxide and C1 to C8 hydrocarbons in natural gas samples using two packed columns. This Malaysian Standard replaces MS ISO 6974:1996. | |
| Price Code : C | |
| MS ISO 6974-4 : 2003 | |
| Natural gas - Determination of composition with defined uncertainty by gas chromatography - Part 4: Determination of nitrogen, carbon dioxide and C1 to C5 and C6+ hydrocarbons for a laboratory and on-line measuring system using two columns (First revision) | |
| This Malaysian Standard is identical with ISO 6974-4:2000. This Malaysian Standard describes a gas chromatographic method for the quantitative determination of natural gas constituents using a two-column system. This Malaysian Standard replaces MS ISO 6974:1996. | |
| Price Code : B | |
| MS ISO 6974-5 : 2003 | |
| Natural gas - Determination of composition with defined uncertainty by gas chromatography - Part 5: Determination of nitrogen, carbon dioxide and C1 to C5 and C6+ hydrocarbons for a laboratory and on-line process application using three columns (First revision) | |
| This Malaysian Standard is identical with ISO 6974-5:2000. This Malaysian Standard describes a gas chromatographic method for the quantitative determination of natural gas constituents using a three-column system. This Malaysian Standard replaces MS ISO 6974:1996. | |
| Price Code : C | |
| MS ISO 6975 : 1997 | |
| Natural gas - Determination of hydrocarbons from butane (C4) to hexadecane (C16) - Gas chromatography method. | |
| This
Malaysian Standard is a total adoption of ISO 6975:1986.
This standard specifies a method of quantitative of C4
to C16. hydrocarbons in natural gas. |
|
| Price Code : B | |
| MS ISO 6976 : 1996 | |
| Natural gas - Calculation of calorific values, density, relative density and Wobbe index from composition | |
| This
Malaysian Standard is a total adoption of ISO 6976 :
1996. This standard specifies method for the calculation of the calorific value [both superior (gross) and inferior (net), density and relative density of natural gas when values for the physical properties of the pure components and the composition of the gas by mole fraction are known. It also describes the determination of the precision of the calculated calorific value from the precision of the method of analysis. |
|
| Price Code : F | |
| MS ISO 6978 : 1996 | |
| Natural gas - Determination of mercury | |
| This
Malaysian Standard is a total adoption of ISO 6978 :
1992. This standard specifies two methods, A and B, for
the determination of mercury, including elemental
mercury, dimethyl mercury and diethyl mercury, in natural
gas. Method A prescribes sampling at atmospheric pressure, using absorption in potassium permanganate solution followed by reduction of mercury ions and subsequent analysis by flameless atomic absorption spectrometry. Method B prescribes sampling at atmospheric or higher pressure using absorption of mercury on silver/gold followed by description and subsequent analysis by flameless atomic absorption spectometry. |
|
| Price Code : B | |
| MS ISO 8943 : 1997 | |
| Refrigerated light hydrocarbon fluids - Sampling of liquefied natural gas- Continuous method. | |
| This
Malaysian Standard is a total adoption of ISO 8943:1991. This standard specifies a method of continuous sampling of LNG whilst it is being transferred through an LNG transfer line. |
|
| Price Code : B | |
| MS ISO 10101-1 : 1997 | |
| Natural gas - Determination of water by the Karl Fischer method : Part 1 : Introduction . | |
| This
Malaysian Standard is a total adoption of ISO
10101-1:1993. This part of standard specifies general
requirements for the determination of water in natural
gas using the Karl Fischer method. |
|
| Price Code : A | |
| MS ISO 10101-2 : 1997 | |
| Natural gas - Determination of water by the Karl Fischer method : Part 2: Titration procedure. | |
| This
Malaysian Standard is a total adoption of ISO
10101-2:1993. This part of standard specifies a
titrimetric procedure for the determination of water
content in natural gas. Volumes are expressed in cubic
meters at a temperature of 273.15 K (0oC) and
a pressure of 101.325 kPa (1atm). It applies to water
concentrations between 5 mg/m3 and 5000 mg/m3. |
|
| Price Code : B | |
| MS ISO 10101-3 : 1997 | |
| Natural gas - Determination of water by the Karl Fischer method : Part 3: Coulometric procedure. | |
| This
Malaysian Standard is a total adoption of ISO
10101-3:1993. This part of standard specifies a
coulometric procedure for the direct determination of
water content by the Karl Fisher method.The method
applies to the natural gas and other gases which do not
react with Karl Fischer reagents. It applies to water
concentrations between 5 mg/m3 and 5000 mg/m3. |
|
| Price Code : B | |
| MS ISO 10715 : 2002 | |
| Natural gas - Sampling guidelines | |
| The purpose
of this Malaysian Standard is to provide concise
guidelines for the collection, conditioning and handling
of representative samples of processed natural gas
streams. It also contains guidelines for sampling
strategy, probe location and the handling and design of
sampling equipment. |
|
| Price Code : E | |
| MS ISO 10723 : 2002 | |
| Natural gas - Performance evaluation for on-line analytical systems | |
| This
Malaysian Standard specifies a method of determining
whether an analytical system for natural gas is
satisfactory, on the assumptions that a) the analytical requirement has been clearly and unambiguously defined, for the range and uncertainty of component concentration measurements, and the uncertainty of properties which may be calculated from these measurements; b) the analytical and calibration procedures have been fully described; c) the method is intended to be applied to gases having compositions which vary over ranges normally found in transmission and distribution networks. |
|
| Price Code : F | |
| MS ISO 13443 : 2003 | |
| Natural gas – Standard reference conditions | |
| This
Malaysian Standard is identical with ISO 13443:1996. This
Malaysian Standard specifies the standard reference
conditions of temperature, pressure and humidity to be
used for measurements and calculations carried out on
natural gases, natural-gas substitutes and similar
fluids. |
|
| Price Code : B | |
| MS ISO 13734 : 2002 | |
| Natural gas - Organic sulfur compounds used as odorants - Requirements and test methods | |
| This
Malaysian Standard specifies requirements and test
methods for organic sulfur compounds suitable for
odorization of natural gas and natural gas substitutes
for public gas supply, hereafter referred to as odorants. |
|
| Price Code : F | |
| MS ISO 14111 : 2002 | |
| Natural gas - Guidelines to traceability in analysis | |
| This
Malaysian Standard provides general guidelines on the
implementation and application of traceability concepts
in the analysis of natural gas. Its purpose is to lay
down the foundations for the development of specific
traceability protocols in other Malaysian Standards for
natural-gas analysis. |
|
| Price Code : D | |
| MS ISO 14532 : 2003 | |
| Natural gas - Vocabulary | |
| This Malaysian Standard establishes the terms, definitions, symbol and abbreviations used in the field of natural gas. | |
| Price RM10 | |
Petroleum products in general |
|
| MS 563 : 1978 | |
| Method of test for distillation of petroleum products. | |
| Covers distillation of motor gasolines, aviations, gasolines, aviations turbine fuels, special boiling point spirit, kerosene, gas oils, distillate fuel oils and similar petroleum products. | |
| Price Code : D | |
| MS 761 : 1982 | |
| Code of practice for the storage and handling of flammable and combustible liquids. | |
| Provides classification, design, construction and operation of installation, Includes petroleum and petroleum products. | |
| Price Code : I  Amendment 1 : 1986 | |
| MS 781 : 1982 | |
| Method of sampling petroleum and petroleum products. | |
| For crude petroleum and its liquid products by manual procedures. From tanks, pipelines, conveyors, open streams at various depts. Does not include electrical insulating oils and gases. | |
| Price Code : D | |
| MS 787 : 1982 | |
| Method for detection of copper corrosion from petroleum products by the copper strip tarnish test. | |
| Detects corrosiveness ot copper due to aviation gasoline, natural gasoline and other hydro-carbon having a reid vapour pressure not grester than 124 kPa (18 P si). | |
| Price Code : B | |
| MS 789 : 1982 | |
| Method of test for sulphur in petroleum products (Lamp method). | |
| Determines total sulphur in liquid petroleum products through 3 procedures namely, a special sulphate analysis, a direct burning procedure and the bleeding procedure. | |
| Price Code : C | |
| MS 800 : 1982 | |
| Specification for aluminium alloy pistons for gasoline and diesel engine applications. | |
| Specifies the requirements for materials, dimensional, weight tolerances, surface finish and quality acceptance. | |
| Price Code : B | |
| MS 845 : 1983 | |
| Method of test for sulphur in petroleum products (high temperature method). | |
| Prescribes two procedures to determine total sulphur in samples boiling at above 177 degrees C for petroleum coke containing up to 8 per cent. | |
| Price Code : B | |
| MS 914 : 1984 | |
| Method of test for flash and fire points by cleveland open cup. | |
| Method suitable for all petroleum products except for fuel oils and products having an open cup flash point (determined by this method) below 79 degrees C. | |
| Price Code : A | |
| MS 960 : 1985 | |
| Method of test for petroleum products and bituminous materials by distillation. | |
| Material is heated under reflux with a water immicable solvent which co distills with the water in the sample. Condensed solvent and water are separated in a trap, where water settle in the graduated section of the trap and the solvent return to the trap. | |
| Price Code : A | |
| MS 962 : 1985 | |
| Method of test for conradson carbon residue of petroleum products. | |
| Describes a procedure for the determination of the amount of carbon residue left after evaporation and pyrolysis of oil and is intended to provide some indication of relative coke-forming properties. The method is generally applicable to relatively non-volatile petroleum products which partially decompose on distillation at atmospheric pressure. | |
| Price Code : B | |
| MS 1077 : Part 1 : 2003 | |
| Method of test for brake fluids: Part 1: Equilibrium reflux boiling point (ERBP) (First revision). | |
| This Malaysian Standard describes the method of determination of the ERBP of a brake fluid. This Malaysian Standard replaces MS 1077: Part 1: 1988. | |
| Price Code : A | |
| MS 1077 : Part 2 : 2003 | |
| Method of test for brake fluids: Part 2: Wet ERBP (First revision). | |
| This Malaysian Standard describes a method for the determination of wet equilibrium reflux boiling point (WET ERBP) of a brake fluid. This Malaysian Standard replaces MS 1077: Part 2: 1988. | |
| Price Code : A | |
| MS 1077 : Part 3 : 2003 | |
| Method of test for brake fluids: Part 3: pH value (First revision). | |
| This Malaysian Standard prescribes a method for the determination of pH value of brake fluid. This Malaysian Standard replaces MS 1077: Part 3: 1987. | |
| Price Code : A | |
| MS 1077 : Part 4 : 2003 | |
| Method of test for brake fluids: Part 4: Fluid stability (First revision). | |
| This Malaysian Standard prescribes a method for evaluating the heat temperature and chemical stability of a brake fluid. This Malaysian Standard replaces MS 1077: Part 4: 1987. | |
| Price Code : A | |
| MS 1077 : Part 5 : 2003 | |
| Method of test for brake fluids: Part 5: Corrosion (First revision). | |
| This Malaysian Standard prescribes a method for evaluation of the corrosiveness of a brake fluid. This Malaysian Standard replaces MS 1077: Part 5: 1988. | |
| Price Code : B> | |
| MS 1077 : Part 6 : 2003 | |
| Method of test for brake fluids: Part 6: Fluidity and appearance at low temperature (First revision) | |
| This Malaysian Standard specifies a method for determining the fluidity and appearance of a sample brake fluid at 40 °C and at 50 °C. This Malaysian Standard replaces MS 1077: Part 6: 1987. | |
| Price Code : B | |
| MS 1077 : Part 7 : 2003 | |
| Method of test for brake fluids: Part 7: Evaporation (First revision) | |
| This Malaysian Standard prescribes a method to determine the evaporation residue and pour point of the evaporation residue of brake fluid. This Malaysian Standard replaces MS 1077: Part 7: 1988. | |
| Price Code : A | |
| MS 1077 : Part 8 : 2003 | |
| Method of test for brake fluids: Part 8: Water tolerance (First revision). | |
| This Malaysian Standard prescribes a method to evaluate the water tolerance characteristics of a brake fluid. This Malaysian Standard replaces MS 1077: Part 8: 1988. | |
| Price Code : A | |
| MS 1114 : Part 1 : 1988 | |
| Method of test for bauxite : Part 1 : Determination of moisture in analytical samples - Gravimetric method. | |
| Specifies a method for the determination of moisture in analytical samples of bauxite. | |
| Price Code : A | |
| MS 1114 : Part 2 : 1990 | |
| Method of test for bauxite : Part 2 : Determination of loss of mass at 1075°C - Gravimetric method. | |
| Specifies a gravimetric method for the determination of the loss of moss of analytical samples of bauxite when heated to constant mass at 1075°C. The method is applicable to all bauxites having loss of mass values in the range of 10% to 35%. | |
| Price Code : A | |
| MS 1114 : Part 3 : 1990 | |
| Method of test for bauxite : Part 3 : Determination of aluminium content - EDTA titrimetric method. | |
| Specifies an EDTA titrimetric method for the determination of aluminium in bauxite. This method is applicable to products having aluminium contents, expressed as aluminium oxide (AI2O3)in the range 30% to 65% (m/m). | |
| Price Code : A | |
| MS 1114 : Part 4 : 1990 | |
| Method of test for bauxite : Part 4 : Determination of total silicon content - Combined gravimetric and spectrophotometric methods. | |
| Specifies a combined gravimetric method and spectrophotometric method for the determination of total silicon in bauxite. This method is applicable to ores containing between 1 and 25% (m/m) of silicon dioxide. | |
| Price Code : B | |
| MS 1114 : Part 5 : 1990 | |
| Method of test for bauxite : Part 5 : Determination of iron content - Titrimetric method. | |
| Specifies a titrimetric method for the determination of iron in bauxite. This method is suitable for use with ores having iron oxide contents ranging from 2% to 50% (m/m). | |
| Price Code : A | |
| MS 1114 : Part 6 : 1990 | |
| Method of test for bauxite : Part 6 : Determination of titanium content - 4.4, Diantipyrylmethane spectrophotometric method. | |
| Specifies 4.4 - diantipyrylmethane spectrophotometric method for the determination of titanium in bauxite. This method is applicable to ores containing between 0.5% and 8% (m/m) of titanium dioxide. | |
| Price Code : B | |
| MS 1114 : Part 7 : 1991 | |
| Methods of test for bauxite : Part 7 : Determination of Phosphorous content - Molybdenum blue spectrophotometric method. | |
| This Malaysian Standard specifies a molybdenum blue spectrophotometric method for the determination of phosphorus in bauxite.The method is applicable to ores having phosphorus contents expressed as diphosphorus pentoxide between 0.01 and 5% (m/m). | |
| Price Code : B | |
| MS ISO 1998-1 : 2003 | |
| Petroleum industry – Terminology – Part 1: Raw materials and products. | |
| This Malaysian Standard is identical with ISO 1998-1:1998. This Malaysian Standard consists of a list of terminology used in the petroleum industry to indicate raw materials or petroleum products. This Malaysian Standard cancels and replaces MS 649: Part 1:1982. | |
| Price Code : D | |
| MS ISO 1998-2 : 2003 | |
| Petroleum industry – Terminology – Part 2: Properties and tests. | |
| This Malaysian Standard is identical with ISO 1998-2:1998. This Malaysian Standard consists of a list of terminology used in the petroleum industry to indicate properties of petroleum products and test methods. This Malaysian Standard cancels and replaces MS 649: Part 2:1980. | |
| Price Code : C | |
| MS ISO 3007 : 2003 | |
| Petroleum products and other liquids – Determination of flash point – ABEL closed cup method. | |
| This Malaysian Standard is identical with ISO 3007:1999. This Malaysian Standard specifies a method for the determination of the vapour pressure of liquid petroleum products consisting of essentially or wholly of hydrocarbon components or containing oxygenated hydrocarbons of specific types and at specified maximum concentrations. The method does not apply outside these concentration levels, nor to any blends containing methanol or other oxygenated hydrocarbons not covered in the following requirements, i.e. the maximum concentrations of ethers containing 5 or more carbon atoms is 15 % (V/V) and for ethanol is 10 % (V/V). For higher alcohols, the maximum concentration is 7 % (V/V). This Malaysian Standard cancels and replaces MS 538:1978. | |
| Price Code : C | |
| MS ISO 3016 : 2003 | |
| Petroleum products – Determination of pour point. | |
| This Malaysian Standard is identical with ISO 3016:1995. This Malaysian Standard specifies a method for the determination of the pour point of petroleum products. A separate procedure suitable for the determination of the lower pour point of fuel oils, heavy lubricant base stock and products containing residual fuel components is also described. This Malaysian Standard cancels and replaces MS 785:1982. | |
| Price Code : B | |
| MS ISO 6245 : 2004 | |
| Petroleum products - Determination of ash | |
| This standard applies to method determination of ash from distillate and residue fuels, crude oils, lubricating oils, waxes, and other petroleum products., in which any ash-forming materials present are normally considered to be undesirable impuruties or contiminants. The method is limited to petroleum products which are free from added ash-forming additives, including certain phosphorous compounds. | |
| Price RM10 | |
| MS ISO 13736 : 2003 | |
| Petroleum products and other liquids – Determination of flash point – ABEL closed cup method. | |
| This Malaysian Standard is identical with ISO 13736:1997. This Malaysian Standard species a method for the determination of the closed cup flash point of petroleum products and other liquids having flash points between –30 °C and 70 °C inclusive. However the precision given for the method is valid for flash points in the range –5 °C to 66.5 °C. This Malaysian Standard cancels and replaces MS 648:1980. | |
| Price Code : C | |
| MS ISO 15403 : 2003 | |
| Natural gas – Designation of the quality of natural gas for use as a compressed fuel for vehicles. | |
| This Malaysian Standard is identical with ISO 15403:2000. This Malaysian Standard provides manufacturers, vehicle operators, fuelling station operators and others involved in the compressed-natural-gas vehicle industry with information on the fuel quality for natural gas vehicles (NGVs) required to develop and operate compressed-natural-gas vehicle equipment successfully. | |
| Price Code : D | |
Lubricants, industrial oils and related products |
|
| MS 379 : 1982 | |
| Viscosity classification for industrial lubricants (First revision). | |
| Establishes a system for classification of viscosity for industrial liquid lubricants and related lubricants. Includes mineral oils used as lubricants, such as hydraulic fluids and other applications. | |
| Price Code : B | |
| MS 380 : 1983 | |
| Specification for steam turbine oils (First revision) | |
| Specifies four viscosity grades of oils which may also be satisfactory for other lubricant purposes. Dos not cover oils of the extreme pressure (E.P.) type. | |
| Price Code : A | |
| MS 381 : 1983 | |
| Specification for straight mineral lubricating oils (First revision). | |
| Specifies group and quality of oils by viscosity grade under additions permitted. | |
| Price Code : A | |
| MS 913 : 1984 | |
| Specification for multipurpose gear lubricating oil petroleum or synthetic base. | |
| Three grades based on viscosity. Chemical and physical requirements. Also include separation, foaming, moisture and copper corrosion, thermal oxidation stability and performance tests. | |
| Price Code : A | |
Hydraulic fluids |
|
| MS 119 : 1990 | |
| Specification for motor vehicle brake fluids (First revision). | |
| Specifies requirements for fluids for use in hydraulic brake systems of motor vehicles, containers for these fluids and labelling of the containers. An additional grade of brake fluids, DOT 5, and the requirements are included. | |
| Price Code : A | |
Waxes, bituminous materials and other petroleum products |
|
| MS 124 : 1996 | |
| Specification for penetration grade of bitumen for use in pavement construction (First revision). | |
| This revised
Malaysian Standard was prepared with a view to supersede
the earlier version of MS 124, published in 1973. Changes
featured in the revised standard include the following: (a) solubility of bitumen is carried out in trichloroethylene instead of carbon disulphide. (b) inclusion of thin film oven test and loss on heating as requirement. (c) insertion of a clause on handling and packaging. (d) to substitute `specific gravity' with `relative density'. |
|
| Price Code : A | |
| MS 159 : 1994 | |
| Specification for cut-back bitumen for use in the construction and/or maintenance of pavement (First revision). | |
| This
Malaysian Standard covers the various grades of cut-back
bitumen of the medium-curing (MC) type for use in the
construction and/or maintenance of pavements. This standard was based mainly on ASTM 2027-76 (1992) Vol (04.03), 'Specification for cutback asphalt (medium-curing type)' with modifications to suit local conditions. This standard shall supersede MS 159 : 1973. The following changes were noted in the revised standard : (1) to include the date of manufacture; (2) the standard only specifies the various grades of medium-curing type of bitumen, omitting the rapid-curing and slowing-curing type of bitumen. |
|
| Price Code : A | |
| MS 160 : 1995 | |
| Specification for bitumen-based coatings for cold application for use in contact with potable water (First revision). | |
| This
Malaysian Standard introduces technical changes that had
been incorporated through the course of revising the
standard. The main changes featured are : (i) The introduction of bitumen-based coatings, type 2, with fillers. Both type 1 and type 2 are further sub- divided into three classes. (ii) Guidance on the use of bitumen-based coatings is also given. (iii) The inclusion of bend resistance test and (iv) Shelf-life requirements. This standard shall supersede MS 160 : 1973. |
|
| Price Code : B | |
| MS 161: 1994 | |
| Specification for cationic bitumen emulsions for use in pavement applications (First revision). | |
| This
Malaysian Standard was first published in 1973 as MS 161
'Specification for bitumen emulsions for use in pavement
applications'. The main changes featured in this first
revision are: (1) Requirements for anionic emulsions are excluded as this type of emulsions are not used in pavement applications; (2) SS 1 Kh grade of cationic emulsion is also excluded as it is also not used in Malaysia to reflect local practice; (3) One extra grade of rapid-setting cationic bitumen emulsion, RS-OK is being included; (4) 'Storage stability test' replaced 'settlement test' to be in line with ASTM D2397-86. In this revision, references were made to: (1) BS 434 : Part 1 : 1984 'Specification for bitumen road emulsions'. (2) ASTM D2397-85 'Specification for cationic emulsified asphalt'. This standard supersedes MS 161 : 1973 'Specification for bitumen emulsions for use in pavement applications'. Amendment 1 : 1995 |
|
| Price Code : A | |
| MS 292 : 1995 | |
| Specification for bitumen based primers for cold or hot application for ferrous products (First revision). | |
| This
Malaysian Standard applies to bitumen based primers,
without fillers, for cold or hot applications, providing
effective bond between the metal and subsequent bitumen
coatings. This standard shall supersede MS 292 : 1975. |
|
| Price Code : A | |
| MS 375 : 1995 | |
| Specification for bituminous emulsions used as a protective coating for roofing (First revision). | |
| This
Malaysian Standard covers emulsified bitumen suitable for
use as a protective coating for built-up roofs and other
exposed surfaces with inclines of not less than 4% or 42
mm/m. |
|
| Price Code : B | |
| MS 378 : 1995 | |
| Specification for use in water-proofing (First revision). | |
| This
Malaysian Standard is the first revision of MS 378 :
1976. This standard covers materials for mastic asphalt
suitable for use in water-proofing the floors of
buildings and bridges, for reservoirs, waterways, subways
and similar structures. It is not intended for use as a
pavement for either foot or vehicular traffic. In the revised version, bitumen is defined as soluble in trichloroethylene instead of carbon disulphide, the former being a safer solvent to use. Where available, test methods shall be quoted against MS instead of ASTM. |
|
| Price Code : A | |
| MS 394 : 1995 | |
| Specification for hot applied bitumen based coationgs for protection against corrosion (First revision). | |
| This
Malaysian Standard covers bitumen based materials both
unfilled and reinforced with minerals or fibrous, inert
fillers, for hot application which will provide effective
coating for iron and steel surfaces against corrosion. In the revised standard, the impact test had been amended to provide for testing at 0°C and at 25°C. The indirect impact test had been omitted. |
|
| Price Code : C | |
| MS 512 : 1977 | |
| Specification for bitumen macadam for roads and other paved areas. | |
| Deals with
composition, manufacture, testing and transport of coated
bitumen macadam for base, levelling and wearing courses.
Recommendations for laying the materials and for
measuring their temperatures are indicated. |
|
| Price Code : D | |
| MS 535 : 1978 | |
| Specification for asphaltic concrete for road pavement and airfield runway by the marshall test method. | |
| Deals with
composition, manufacture, design and testing, and
transport of asphaltic concrete for base and wearing
courses in the surfacing of heavy duty roads and
motor-ways. Recommendations for laying asphaltic concrete
and for measuring their temperature are also indicated. |
|
| Price Code : C | |
| MS 539 : 1995 | |
| Methods of sampling bituminous materials (First revision). | |
| This
Malaysian Standard applies to the sampling of bituminous
materials at points of manufacture, storage, or delivery.
Only minor editorial errors were identified throughout
the revision exercise. Current practise of local
industries were also taken into consideration. Basically,
the standard is similar to ASTM 'Method D140-70
Bituminous material, sampling'. This standard shall
supersede MS 539 : 1973. |
|
| Price Code : B | |
| MS 541 : 1995 | |
| Method for determination of penetration of bituminous materials (First revision). | |
| This
Malaysian Standard is a revision of MS 541 : 1978. The method describes a procedure for determining the penetration of semi solid and solid bituminous materials. Changes involved editorial amendments and the replacement of Imperial units with metric units. This standard shall supersede MS 541 : 1978. |
|
| Price Code : B | |
| MS 572 : 1996 | |
| Method of test for ductility of bituminous materials (First revision) | |
| This
Malaysian Standard is intended for the determination of
the ductility of a bituminous material measured by the
distance to which it will elongate before breaking when
to ends of a briquet specimen of the material are pulled
apart at a specified speed and at a specified
temperature. |
|
| Price Code : A | |
| MS 574 : 1995 | |
| Method of test for distillation of cut-back bituminous products (First revision). | |
| This
Malaysian Standard measures the amount of the more
volatile constituents in cut-back bituminous products. In the revised version, values expressed in imperial units have been substituted with metric units. Since local cut-back bituminous products are of non coal-tar origin, further distillation is not necessary. This standard shall supersede MS 574 :1979. |
|
| Price Code : B | |
| MS 650 : 1995 | |
| Method of test for relative density of solid pitch and bitumen - Displacement method (First revision). | |
| This
Malaysian Standard is a revised standard of MS 650, first
published in 1980. In the course of the revision, the main changes featured include: (i) The use of the term 'relative density' instead of 'specific gravity' and its definition. (ii) The use of freshly boiled distilled water instead of freshly distilled water. This is to minimized entrapped air bubbles. (iii) The expression of results in terms of relative density at 25°C instead of specific gravity 25°/25°C. This standard shall supersede MS 650 : 1980. |
|
| Price Code : A | |
| MS 685 : 1996 | |
| Method of test for specific gravity and density of semi-solid bituminuous materials (First revision) | |
| This
Malaysian Standard covers the determination of the
specific gravity and density of semi-solid bituminous
materials, asphalt cements and soft tar pitches by use of
a pycnometer. |
|
| Price Code : A | |
| MS 687 : 1995 | |
| Method of test for softening point of bitumen (ring-and-ball apparatus) (First revision). | |
| This
Malaysian Standard prescribes the determination of the
softening point of bitumen in the range from 30 to
157°C. In the revised version, the main changes featured include: (i) Definition of softening point expressed as follows 'temperature at which a substance attains a particular degree of softness under specified conditions of test'. (ii) The significance or usefulness of the 'softening point' value. (iii) The use of different reagents/materials softening point range. (iv) The use of releasing agent to prevent adhesion of bitumen to the pouring plate. This standard shall supersede MS 687 : 1981. |
|
| Price Code : B | |
| MS 689 : 1981 | |
| Specification for bitumen-based filling compounds for electrical purposes. | |
| Specifies
requirements, classification and test methods. Excludes
oils and oil resisting compounds, cold pouring compounds
and those designed for special purposes. |
|
| Price Code : C Amendment 1 : 1995 | |
| MS 782 : 1997 | |
| Method of test for kinetic of bitumens (First revision). | |
| This
Malaysian Standard test method covers procedures for the
determination of kinematic viscosity of liquid bitumens,
roads oils and distillation residues liquid bitumens all
at 60°C and of bitumen cements at 135°C in the range
from 6 to 100 000 cst. This standard supersedes MS 782 :
1982. |
|
| Price Code : B | |
| MS 783 : 1997 | |
| Method of test for absolute viscosity of bitumens by vacuum capillary viscometers (First revision). | |
| This
Malaysian standard specifies the procedures for the
determination of viscosity of bitumen by vacuum capillary
viscometers at 60°C. It is applicable to materials
having viscosities in the range from 0.036 to over 200
000 P. This standard supersedes MS 783 : 1982. |
|
| Price Code : B | |
| MS 784 : 1982 | |
| Method of test for engler specific viscosity of tar products. | |
| Applies to
tars and their fluid products. Does not include absolute
viscosity determination but only empirical flow test. |
|
| Price Code : A | |
| MS 1050 : 1986 | |
| Specification for asphalt damping sheets for motor vehicles. | |
| Specifies
material and performance requirements for heat fusion
type asphalt sheets used as damping material on the floor
of motor vehicles. |
|
| Price Code : B | |
Fuels |
|
Liquid fuels |
|
| MS 117 : 1998 | |
| Specification for kerosene (Second revision). | |
| This
Malaysian Standard is the second revision of MS 117,
Specification for Kerosene. The standard prescribes the
requirements for two grades of kerosene, suitable for use
as an illuminate, solvent and fuel. In the revised
standard, the super grade kerosene was taken out because
it was not applicable to the market conditions. Apart
from that, the copper corrosion test and flock test was
deleted. The revised standard supersedes MS 117 : 1986,
Specification for Kerosene (First revision). |
|
| Price Code : A | |
| MS 118 : Part 2 : 1993 | |
| Specification for motor vehicle gasoline : Part 2 : Unleaded gasoline. | |
| This
Malaysian Standard specifies the requirements for
unleaded motor gasoline suitable for use in spark
ignition engines. The material is also known as petrol in
the automobile industry. |
|
| Price Code : A | |
| MS 122 : 1998 | |
| Specification for fuel oils for use in engines and burning equipment (Second revision). | |
| This
Malaysian Standard specifies the requirements for three
grades of fuel oils suitable for use in engine and
burning equipment in the industrial and marine fields. The revision was undertaken to incorporate several amendments and update the standard. Amongst the charges are: (1) To classify the three grades into light fuel oil, medium fuel oil and heavy fuel oil respectively. (2) The minimum flash point be amended from 66°C to 60°C. (3) The % mass sulphur for all the grades was reduced to 3.5. (4) Where the term specific energy/gravity appears it shall be read as calorific value. This revised standard shall supersede MS 122 : 1986, Specification for fuel oils for use in engines and building equipment (First revision). |
|
| Price Code : A | |
| MS 123 : 1993 | |
| Specification for diesel fuel (Second revision). | |
| This
Malaysian Standard specifies the requirements for diesel
suitable for use in automotive, industrial and other
diesel applications. |
|
| Price Code : A  Amendment 1 : 1998 | |
| MS 376 : 1986 | |
| Specification for crankcase oils (First revision). | |
| Covers all
automotive gasoline and diesel engines, and also high
speed industrial diesel engines. |
|
| Price Code : B | |
| MS 540 : 1978 | |
| Method of test for lead in gasoline, gravimetric method. | |
| Covers
gasoline and other volatile distillates blended with lead
alkyls. Concentration range from 0.05 g to 1.3 g
lead/litre.. |
|
| Price Code : A | |
| MS 575 : 1998 | |
| Specification for jet aviation fuel (First revision) | |
| This
Malaysian Standard prescribes the specification of the
Jet A-1 type of aviation turbine fuel which is a
relatively high flash-point distillate to the kerosene
type. This document represents the most stringent
requirements of an aviation fuel adopted by the world's
major oil industries. This revised standard shall
supersede MS 575 : 1979, Specification for jet aviation
fuel. |
|
| Price Code : A | |
| MS 576 : 1979 | |
| Specification for aviation gasoline. | |
| Prescribes
requirements for one grade of aviation gasoline AVGAS-100
for use in civil and military aircraft piston engines.
Requirements tabulated with reference standards. |
|
| Price Code : A | |
| MS 686 : 1981 | |
| Method of test for flash and fire points by Pensky-Martens closed tester. | |
| Covers
determination for fuel oils, lube oils, suspensions of
soluids, liquids that tend to form a surface film under
test conditions and other liquids. |
|
| Price Code : B | |
| MS 786 : 1982 | |
| Method of test for oxidation stability of gasoline (induction period method). | |
| Determine
stability of gasoline under accelerated oxidation
condition. Gum formulation during storage correlates with
different storage conditions. |
|
| Price Code : B | |
| MS 788 : 1982 | |
| Method of test for existent gum in fuels by jet evaporation. | |
| Determines
existent gum in motor gasoline and aircraft fuels at time
of test. |
|
| Price Code : B | |
| MS 846 : 1983 | |
| Method for burning test (24 hour) for kerosene. | |
| Outlines
procedure to evaluate the burning properties of kerosene;
through wickchar forming tendencies. |
|
| Price Code : A | |
| MS 874 : 1984 | |
| Method of test for smoke point of aviation turbine fuels. | |
| Specifies
apparatus and reagent to be used for test procedures to
determine sulphur content of more than 1 ppm. |
|
| Price Code : B | |
| MS 910 : 1984 | |
| Method of test for knock characteristics of motor and aviation fuels by the motor method. | |
| Covers the
determination of the knock characteristics of motor and
aviation gasolines intended for use in spark-ignition
engines. |
|
| Price Code : D | |
| MS 911 : 1984 | |
| Method of test for knock characteristics of motor fuels by the research method. | |
| Covers the
determination of the knock characteristics of motor
gasolines, intended for use in spark-ignition in terms of
research octane numbers. |
|
| Price Code : C | |
| MS 912 : 1984 | |
| Method of test for lead in gasoline (Iodine monochloride method). | |
| Specifies a
method for the determination of total lead in gasoline
containing lead alkyls at concentrations between 0.03 g
and 1.0 g of lead per litre. |
|
| Price Code : A | |
| MS 959 : 1985 | |
| Method of test for kinetic viscosity of transparent and opaque liquids and calculation of dynamic viscosity. | |
| Method
specifically applies to liquid petroleum products where
kinetic viscosity if related to the time taken for a
volume of liquid to flow under gravity through a
calibrated glass capillary viscometer. Dynamic viscosity
can be obtained by multiplying the measured kinetic
viscosity with the density of the liquid. |
|
| Price Code : B | |
| MS 961 : 1985 | |
| Method of test for water and sediment in fuel oils by centrifuge. | |
| Lists out
apparatus, solvent, sampling, procedure, calculation and
report and precision required. |
|
| Price Code : A | |
| MS 1254: 1992 | |
| Method of test for lead in gasoline by atomic absorption spectrometry. | |
| This
Malaysian Standard test method covers, the determination
of the total lead content of gasoline within the
concentration range of 0.010 to 0.10 of lead/U.S. gal
(2.5 to 25 mg/litre). The method compensates for
variations if gasoline composition and is independent of
lead alkyl type. |
|
| Price Code : A | |
Gaseous fuels |
|
| MS 158 : 1998 | |
| Specification for liquefied petroleum gases (LPG) (Second revision) | |
| This Malaysian Standard describes the product characteristics such as vapour pressure, volatile residue, residual matter, volatile sulphur, moisture content and free water content for four basic types of liquefied petroleum gases.This revised standard shall supersede MS 158 : 1985, Specification for LPG (First revision). | |
| Price Code : A | |
| MS 537 : 2001 | |
| Method of test for volatility of liquefied petroleum gases (First revision) | |
| This test method is a measure of the relative purity of the various types of liquefied petroleum gases (LPG) and helps to ensure suitable volatility performance. The test results, when properly related to vapour pressure and density of the product, can be used to indicate the presence of butane and heavier components in propane-butane and butane type fuels. The presence of hydrocarbon compounds less volatile than those of which the LPG is primarily composed is indicated by an increase in the 95% evaporated temperature. This standard supersedes MS 537 : 1978. | |
| Price Code : B | |
| MS 564 : 2000 | |
| Method of sampling liquefied petroleum gases (LPG)(First Revision) | |
| This Malaysian Standard covers procedures for obtaining representative samples of LPG such as propane, butane or mixture thereof in containers other than those used in laboratory testing apparatus.This standard supersedes MS 564 : 1978 | |
| Price Code : A | |
| MS 573 : 2000 | |
| Method of test for vapour pressure of liquefied petroleum gases (LPG - Method) (First revision) | |
| This Malaysian Standard covers the method of test for determining the gauge vapour pressure of liquefied petroleum gas at the temperature of 37.8 degrees celcius to 70 degrees celcius (158 degrees fahrenheit). This standard supersede MS 573 : 1979 | |
| Price Code : B | |
| MS 830 : 1994 | |
| Code of practice for the storage, handling and transportation of LPG (First revision). | |
| This Malaysian Standard sets out fundamental requirements for the design, construction and safe operation of installations for the storage, handling and transportation of LPG. It is a first revision of the Malaysian Standard MS 830 : 1986. In this revised version, a new section is incorporated to carter for the safety aspects of LPG containers attached to mobile gas-fired equipment. | |
| Price Code : Q | |
| MS 875 : 2001 | |
| Method of test for sulphur in liquefied petroleum gases (Oxy-hydrogen burner or lamp) (First revision) | |
| This test method covers the determination of total sulphur in liquefied petroleum gases containing more than 1 mg/g. Specimens should not contain more than 100 mg/g of halogens. This standard supersedes MS 875 : 1984. | |
| Price Code : B | |
| MS 1086 : 1987 | |
| Specification for buried polyethylene (PE) pipes for the supply of gaseous fuels. | |
| Applies to pipes of nominal outside diameters ranging from 20 mm to 630 mm made from polyethylene (PE) for use in the supply of gaseous fuels at pressures not exceeding 0.4 MPa (4bar) and temperature not exceeding 35°C. | |
| Price Code : B | |
Petroleum products and natural gas handling equipment |
|
| MS 930 : 1986 | |
| Code of practice for the installation of fuel gas piping systems and appliances. | |
| Covers gas piping design, materials and components; installations; inspection, testing and purging; installation of general specific equipment; venting of equipment; equipment operation and modification. | |
| Price Code : Q | |
| MS 1748 : 2004 | |
| Offshore pipeline systems | |
| This
Malaysian standard specifies requirements and gives
recommendations for the design, materials, installation,
testing, operation, maintenance and abandonment of
pipeline systems used for transportation in the
petroleum and natural gas industries. |
|
| Price RM110 | |
| MS ISO 3183-1 : 2003 | |
| Petroleum
and natural gas industries - Steel pipe for pipelines
technical delivery conditions Part 1: Pipes of
requirement class A |
|
| This part of MS ISO 3183 specifies the technical delivery conditions for seamless and welded pipe of non-alloy and alloy (except stainless) steels with the basic Quality and testing requirements (level A), which are intended for the transmission and distribution of combustible and non-combustible fluids (including water) in the petroleum and natural gas industries | |
| Price RM120 | |
| MS ISO 3183-2 : 2003 | |
| Petroleum
and natural gas industries - Steel pipe for pipelines -
Technical delivery conditions - Part 2: Pipes of
requirement class B |
|
| This part
of MS ISO 3183 specifies the technical delivery
conditions for unalloyed and alloyed (except stainless)
seamless an welded steel pipes. |
|
| Price RM60 | |
| MS ISO 3183-3 : 2003 | |
| Petroleum
and natural gas industries - Steel pipe for pipelines -
Technical delivery conditions : Part 3 : Pipes of
requirement class C |
|
| This part
of MS ISO 3183 specifies the technical delivery
conditions for unalloyed and alloyed (except stainless)
seamless and welded steel pipes |
|
| Price RM70 | |
| |
|