| |
|
87 |
PAINT AND COLOUR INDUSTRIES |
Paint coating process |
|
Paints and varnishes |
|
| MS 125 : 1995 | |
| Specification for gloss enamel paint (Second revision). | |
| This revised
Malaysian Standard specifies an air drying gloss enamel
paint for use on primer interior and exterior wood and
metal surfaces and for recoating of previously painted
surfaces, provided the surface is in sound condition and
suitable for receiving such a coating. Amendment 1:1997 |
|
| Price Code : A | |
| MS 132 : 1993 | |
| Specification for undercoating paint for use under gloss enamel paint (First revision). | |
| This revised
Malaysian Standard prescribed requirements for
undercoating paint to be used on primer interior and
exterior metal and timber surfaces under gloss enamel
paint or its equivalent. Under this revision, the main
changes featured are in the composition and also
properties of the undercoating paint. This standard
supersedes MS 132 : 1973, "Specification for
undercoating paint for use in paints : Finishing, gloss
enamel, air drying". |
|
| Price Code : A | |
| MS 133 : 1973 | |
| Methods of test for paints : General introduction. | |
| Price Code : A | |
| MS 133 : Part A1 : 1973 | |
| Methods of test for paints : Part A1 : Sampling of products in liquids or paste form (First revision). | |
| This
Malaysian Standard specifies both the procedure for
preliminary examination of a single samples as received
for testing and the procedure for preparing a test sample
by blending and reduction of a series of samples
representative of consignment of bulk paints, varnishes
or related products. |
|
| Price Code : B | |
| MS 133 : Part A2 : 1993 | |
| Methods of test for paints : Part A2 : Examination and preparation of samples for testing (First revision). | |
| This
Malaysian Standard specifies both the procedure for
preliminary examination of a single samples as received
for testing and the procedure for preparing a test sample
by blending and reduction of a series of samples
representative of consignment of bulk paints, varnishes
or related products. |
|
| Price Code : A | |
| MS 133 : Part A3 : 1989 | |
| Methods of test for paints : Part A3 : Standard panels for paint testing (First Revision) | |
| Price Code : B | |
| MS 133 : Part A4 : 1973 | |
| Methods of test for paints : Part A4 : Notes for guidance on paint application. | |
| Gives
guidance notes on application of paint for laboratory
examination. Brushing, spraying and dipping techniques
and method of drying are described. |
|
| Price Code : B | |
| MS 133 : Part A5 : 1993 | |
| Methods of test for paints : Part A5 : Large scale brushing test (First revision). | |
| This
Malaysian Standard described procedures primarily
intended for assessing the brushing and flow
characteristics of paints and related materials when
applied to relatively large areas of closely defined
substrate. |
|
| Price Code : B | |
| MS 133 : Part A6 : 1993 | |
| Methods of test for paints : Part A6 : Determination for flow time by use of BS flow cups (First revision). | |
| This revised
Malaysian Standard specifies the break-point procedure
for determining flow time by used of BS flow cups of
paints and varnishes. The fixed volume procedure were
deleted as it was not being practised in the local paint
industry. |
|
| Price Code : A | |
| MS 133 : Part A7 : 1994 | |
| Methods of test for paints : Part A7 : Determination of viscosity at a high rate of shear (First revision). | |
| This
Malaysian Standard specifies the procedure for
determining the dynamic viscosity of paints and varnishes
at a rate of shear in the range of 5000s-1 to
20000s-1 using viscometer of the cone and
plate or concentric cylinder type. This standard is intended to supersede MS 133 : Part A7 : 1973,'Methods of test for paints : Determination of the viscosity of paint at a high rate of shear'. |
|
| Price Code : A | |
| MS 133 : Part A8 : 1994 | |
| Methods of test for paints : Part A8 : Flash/no flash test-closed cup equilibrium method (First revision). | |
| This part of
the revised Malaysian Standard prescribes the procedure
for determining whether or not flashing occurs at a
single given temperature in flammable material. The
method is suitable for use over the temperature range of
5-65°C. This standard is technically identical to ISO
1516 : 1981 and it is intended to supersede MS 133 : Part
A8 : 1973. |
|
| Price Code : A | |
| MS 133 : Part A9 : 1994 | |
| Methods of test for paints : Part A9 : Consistency by use of stomer viscometer (First revision). | |
| This part of
the revised Malaysian Standard describes the procedure
for determining consistency of paints and varnishes using
the Stormer Viscometer equipped with stroboscopic timer,
liquid crystal Display, digital model KU-1 and also
Stormer Viscometer without stroboscopic attachment. This
standard was based on ASTM D562-81 (Reapproved 1990) and
it is intended to supersede MS 133 : Part A9 : 1973. |
|
| Price Code : A | |
| MS 133 : Part A10 : 1994 | |
| Methods of test for paints : Part A10 : Determination of flash point using closed method (First revision). | |
| This part of
the revised Malaysian Standard prescribes the method for
determination of flash point by using closed cup method
and is suitable for use over the temperature range of 5
to 110°C. This standard is technically identical to ISO 1523 and it is intended to supersede MS 133 : Part A10 : 1973. |
|
| Price Code : B | |
| MS 133 : Part A12 : 1994 | |
| Methods of test for paints : Part A12 : Determination of density and specific gravity (First revision). | |
| This part of
the revised Malaysian Standard prescribes the method for
determination of density and specific gravity by use of a
pyknometer or a mass per volume cup. In the revision of
this standard, reference was made to ISO 2811 taking into
consideration current practices in the local paint
industry. It is intended to supersede MS 133 : Part A12 :
1982. |
|
| Price Code : A | |
| MS 133 : Part A13 : 1994 | |
| Methods of test for paints : Part A13 : Determination of flow time by use of ISO 2431 flow cups. | |
| This part of
Malaysian Standard outlines the procedure for
determination of flow time for paints and varnishes by
use of ISO 2431 flow cups. This standard is an adaptation
of ISO 2431-1984 on 'Determination of flow time by use of
flow cups' with slight modification in order to suit the
local conditions. |
|
| Price Code : B | |
| MS 133 : Part A14 : 1996 | |
| Methods of test for paints and varnishes and their raw materials : Part A14 : Temperatures and humidities for conditioning and testing. | |
| This
Malaysian Standard specifies conditions of temperatures
and relative humidity for general use in the conditioning
and testing of paints and varnishes and their raw
materials. It is applicable to paints and varnishes in
liquid or powder form, to wet or dry films, and their raw
materials. |
|
| Price Code : A | |
| MS 133 : Part B1 : 1998 | |
| Methods of test for paints and varnishes : Part B1 : Determination of water by Dean and Stark method (First revision). | |
| This part of
Malaysian Standard Method describes a procedure
determination of water in paints and varnishes. Two
methods are given for the procedures; the Dean and Stark
Method and Karl Fisher Method. The Dean and Stark Method
should be used as the referee method on cases of dispute. |
|
| Price Code : C | |
| MS 133 : Part B2 : 1997 | |
| Methods of test for paints and varnishes : Part B2 : Determination of non volatile matter (First revision). | |
| This revised
Malaysian Standard specifies a method for determining the
non-volatile matter content by mass of paints and
varnishes, as well as resin and resin solutions that are
intended for use as binder and varnishes. In the revision
of this standard, reference was made to ISO 3251 : 1993
'Paints and varnishes - Determination of non-volatile
matter of paints, varnishes and binders', taking into
consideration current practice of the local paint
industry. This standard is intended to supersede MS 133 :
Part B2 : 1973. |
|
| Price Code : A | |
| MS 133 : Part B3 : 1998 | |
| Methods of test for paints : Part B3 : Determination of pigment content (Centrifuge) (First revision). | |
| Price Code : A | |
| MS 133: Part B4 : 1997 | |
| Methods of test for paints and varnishes : Part B4 : Determination of total lead by flame atomic absorption spectometric method.(First revision). | |
| This revised
Malaysian Standard specifies a method for determining
total lead in paints and related products. The method is
applicable to products having total lead contents in the
range of about 0.01 to 2% (m/m). In the revision of this
standard, reference was made to ISO 6503 ' Paints and
varnishes - Determination of total lead paints flame
atomic absorption spectrometric method' taking into
consideration current practice of the local paint
industry. This standard is intended to supersede MS 133 :
Part B3 : 1973. |
|
| Price Code : B | |
| MS 133: Part B5 : 1997 | |
| Method of test for paints and varnishes: Part B5 : Determination of soluble lead by atomic absorption spectometric method and dithizone spectrophotometric method. | |
| This
Malaysian Standard specifies two methods for determining
lead content of the test solution. The methods are
applicable to paints having "soluble" lead
contents in the range of about 0.05 to 5% (m/m). This standard, is equivalent to ISO 3856-1 : 1984. This standard should be used in conjunction with MS 133 : Part B4 'Methods of test for paints and varnishes : Part B4 : Determination of total lead flame atomic absorption spectrometric method'. |
|
| Price Code : B | |
| MS 133 : Part B6 : 1999 | |
| Methods of test for paints and varnishes : Part B6 : Determination of soluble antimony content - Flame atomic absorption spectrometric method and rhodamine b spectrophotometric method. | |
| Describes
two methods for the determination of the antimony content
of the test solutions prepared according to MS 1431 or
other suitable Malaysian Standards. The methods are
applicable to paints having "soluble" antimony
contents in the range of about 0.05 to 5 % (m/m). The
flame atomic absorption spectrometric (AAS) method
(Clause 3) should be used as the reference method in
cases of dispute. Other methods can be used by agreement
between the interested parties. If a spectrophotometric
method is agreed, the Rhodamine B spectrophotometric
method (Clause 4) should be used. This standard is
technically equivalent to ISO 3856/2 : 1984. |
|
| Price Code : B | |
| MS 133 : Part B7 : 1999 | |
| Methods of test for paints and varnishes : Part B7 : Determination of soluble barium content - Flame atomic emission spectrometric method. | |
| Describes a
flame atomic emission spectrometric (AES) method for the
determination of the barium content of the test solutions
prepared according to MS 1431 or other suitable Malaysian
Standards. The method is applicable to paints having
"soluble" barium contents in the range of about
0.05 to 5 % (m/m). Other methods can be used by agreement
between the interested parties but this method is the
referee method in cases of dispute. This standard is
technically equivalent to ISO 3856/3 : 1984. |
|
| Price Code : A | |
| MS 133 : Part B8 : 1999 | |
| Methods of test for paint and varnishes : Part B8 : Determination of soluble cadmium content - Flame atomic absorption spectrometric method and polarographic method. | |
| Describes
two methods for the determination of the cadmium content
of the test solutions prepared according to MS 1431 or
other suitable Malaysian Standards. The methods are
applicable to paints having "soluble" cadmium
contents in the range of about 0.05 to 5 % (m/m). The
flame atomic absorption spectrometric method (AAS)
(Clause 3) should be used as the referee method in cases
of dispute. Other methods can be used by agreement
between the interested parties. A polarographic method is
given in Clause 4. This standard is technically
equivalent to ISO 3856/4 : 1984. |
|
| Price Code : B | |
| MS 133 : Part B9 : 1999 | |
| Methods of test for paints and varnishes : Part B9 : Determination of soluble hexavalent chromium content of the pigment portion of the liquid paint or the paint in powder form - diphenylcarbazide spectrophotometric method | |
| Describes a
diphenylcarbazide spectrophotometric method for the
determination of the "soluble" hexavalent
chromium content of the hydrochloric acid extract of the
pigment portion of the liquid paint or of the paint in
powder form, prepared in accordance with 8.2.3 of MS 1431
or other suitable Malaysian Standards. The method is
applicable to paints having hexavalent chromium contents
in the range of about 0.05 to 5 % (m/m). Other methods
can be used by agreement between the interested parties,
provided that the methods are specific for hexavalent
chromium but this spectrophotometric method is the
referee method in cases of dispute. This standard is
technically equivalent to ISO 3856/5 : 1984. |
|
| Price Code : A | |
| MS 133 : Part B10 : 1999 | |
| Methods of test for paints and varnishes : Part B10 : Determination of soluble total chromium content | |
| of the
liquid portion of the paint - flame atomic absorption
spectrometric method. Describes a flame atomic absorption spectrometric (AAS) method for the determination of the total chromium content of the liquid portion of the paint, prepared in accordance with 9.3 of MS 1431 or other suitable Malaysian Standards. The method is applicable to paints having total chromium contents in the liquid portion in the range of about 0.05 to 5 % (m/m). Other methods can be used by agreement between the interested parties but this AAS method is the referee method in cases of dispute. This standard is technically equivalent to ISO 3856/6 : 1984. |
|
| Price Code : B | |
| MS 133 : Part B11 : 1999 | |
| Methods of test for paints and varnishes : Part B11 : Determination of soluble mercury content of the pigment portion of the paint and of the liquid portion of water-dilutable paints - flameless atomic absorption spectrometric method | |
| Describes a
flameless atomic absorption spectrometric method for the
determination of the mercury content of the test
solutions, prepared according to MS 1431 or other
suitable Malaysian Standards. The method is applicable to
paints having "soluble" mercury contents in the
range of about 0.005 to 0.05 % (m/m), but the part of
this method covering the examination of the liquid
portion of the paint is restricted to water-dilutable
paints. This standard is technically equivalent to ISO
3856/7 : 1984. |
|
| Price Code : B | |
| MS 133 : Part C1 : 1996 | |
| Methods of test for paints and varnishes : Part C1 : Determination wet edge time (First revision). | |
| This revised
Malaysian Standard describes a procedure for determining
whether the edge of a film of paint or allied material
remains 'alive' after a specified period of drying, when
applied over the appropriate surface. This standard
supersedes MS 133 : Part C1 : 1973. |
|
| Price Code : A | |
| MS 133 : Part C2 : 1996 | |
| Methods of test for paints and varnishes : Part C2 : Surface-drying time (Ballotini method) (First revision). | |
| This revised
Malaysian Standard specifies a method for determining the
surface-drying characteristics of a coating of a paint or
varnish which dries by the action of air or by chemical
reaction of its components. The method is not intended to
apply to storing products. This standard supersedes MS
133 : Part C2 : 1973. |
|
| Price Code : A | |
| MS 133 : Part C3 : 1996 | |
| Methods of test for paints and varnishes : Part C3 : Through-dry test (First revision). | |
| This revised
Malaysian Standard specifies a test method for
determining under standard conditions whether a single
coat or a multi-coat system of paint or related material
has after a specified drying period, reached the
through-dry state, i.e. a pass/fail test. The test
procedure may also be used to determine the time taken to
achieve that state. This standard supersedes MS 133 : Part C3 : 1973. |
|
| Price Code : B | |
| MS 133 : Part C4 : 1973 (Confirmed 1997) | |
| Methods of test for paints and varnishes : Part C4 : Freedom from residual tack. | |
| Methods of
test for paints and varnishes - Freedom for residual tack
(Confirmed). |
|
| Price Code : A | |
| MS 133 : Part C5 : 1997 | |
| Methods of test for paints and varnishes : Part C5 : Determination of film thickness (First revision). | |
| This revised
Malaysian Standard describes a number of methods that are
applicable to the measurement of the thickness of
coatings applied to a substrate. Some of the techniques
described can be adopted for the measurement of the
thickness of detached coatings. This standard supersedes
MS 133 : Part C5 : 1973. |
|
| Price Code : C | |
| MS 133 : Part C6 : 1997 | |
| Methods of test for paints and varnishes : Part C6 : Determination of fineness of grind (First revision). | |
| This revised
Malaysian Standard specifies a method for determining the
fineness of grind of paint and related products by use of
a suitable gauge, graduated in micrometers. This standard
is intended to supersede MS 133 : Part C6 : 1973. |
|
| Price Code : B | |
| MS 133 : Part C7 : 1997 | |
| Methods of test for paints and varnishes : Part C7 : Determination of drying time using BK drying recorder (Surface dry, touched dry and hard dry). | |
| This
Malaysian Standard specifies a method for determining the
drying time (Surface dry, touched dry and hard dry) of
paints and varnishes using BK Drying recorder. This
apparatus is designed for the provision of reliable data
on the transitional stages of drying or curing of paints
and varnished coatings without the need to monitor the
process continuously. In the preparation of this
standard, reference was made to information provided by
the Malaysian Paints Manufacturers Association. |
|
| Price Code : A | |
| MS 133 : Part D1 : 1998 | |
| Methods of test for paints and varnishes : Part D1 : Visual comparison of the colour of paints (First revision) | |
| This
Malaysian Standard specifies a method for the visual
comparison of the colour of films of paints or related
products against a standard (either a reference standard
or a freshly prepared standard ) using either diffuse
daylight or artificial daylight in a standard booth. |
|
| Price Code : A | |
| MS 133 : Part D4 : 1998 | |
| Methods of test for paints and varnishes : Part D4 : Comparison of contrast ratio ( hiding power ) of paints of the same type and colour ( First revision). | |
| Specifies
the standard method to be used in comparing the contrast
ratios given by paints films of white or light colours of
reflectance factor greater than 40% dried at normal air
temperatures and applied at approximately equal wet film
thickness to black and white substrates. |
|
| Price Code : A | |
| MS 133 : Part D5 : 1997 | |
| Methods of test for paints : Part D5 : Measurement of specular gloss of non-metallic paint film at 20(, 60( and 85( (First revision). | |
| The revised
Malaysian Standard specifies a method for determining the
specular gloss of paint film using a reflectometer
geometry at 20°, 60° and 85°. This method is not
suitable for the measurement of the gloss of metallic
paints. This standard supersede MS 133 : Part D5 : 1987. |
|
| Price Code : B | |
| MS 133 : Part D6 : 1999 | |
| Method of test for paints and varnishes : Part D6 : Determination of contrast ratio (opacity) of light coloured paints at a fixed spreading rate (using black and white charts) | |
| Specifies a
method to be used for determining the opacity (by
contrast ratio measurement) given by paint films of white
or light colours of reflectance value greater than 25 %,
applied at a spreading rate of 20 m2/l to an agreed black and white
substrate. This standard is technically equivalent to ISO
3905 : 1980 except for Clause 4.1 and Clause 6.3. |
|
| Price Code : A | |
| MS 133 : Part D7 : 1999 | |
| Methods of test for paints and varnishes : Part D7 : Determination of contrast ratio (opacity) of light coloured paints at a fixed spreading rate (using polyester film) | |
| Specifies a
method to be used for determining the opacity (by
contrast ratio measurement) given by paint films of white
or light colours of reflectance value greater than 25 %,
applied at a spreading rate of 20 m2/l to colourless transparent
polyester film, the reflectance being measured
subsequently over agreed black and white glass plates.
This standard is technically equivalent to ISO 3906 :
1980 except for Clause 6.3 |
|
| Price Code : A | |
| MS 133 : Part D8 : 1999 | |
| Methods of test for paints and varnishes : Part D8 : Determination of hiding power using kubelka-munk method for white and light-coloured paints. | |
| Specifies a
method to be used for determining hiding power (spreading
rate necessary to give a contrast ratio of 98 %) of white
or light-coloured paints. It is restricted to paint films
having the tri-stimulus value of Y ³
70. It is not applicable to fluorescent or metallic
paint. This standard is technically equivalent to ISO
6504/1 : 1983 except for Clause 7.2.1.3. |
|
| Price Code : 00 | |
| MS 133 : Part D9 : 1999 | |
| Method of test for paints and varnishes : Part D9 : Colorimetry - Principles | |
| Describes to
colorimetric terms and fundamental requirements necessary
for determining the colour co-ordinates of paint films
and related materials. This standard is technically
equivalent to ISO 7724/1 : 1984 except for an addition of
a colour photo of the colour co-ordinates in CIE 1976
colour space. |
|
| Price Code : 00 | |
| MS 133 : Part D10 : 1999 | |
| Method of test for paints and varnishes : Part D10 : Colorimetry - Colour measurement | |
| Describes
the method for determining the colour co-ordinates of
paint films. The method is only applicable to paint films
that appear to be uniformly of one colour, i.e.
monochromatic, when examined with normal vision. Paint
films that do not completely hide a non-transparent
substrate represent an opaque system and may be measured
by using the procedure described in this part of MS 133 :
Part D10. Luminescent paint films, transparent paint
films and translucent paint films (for example for
displays or lamp glass), retroreflecting paint films (for
example for traffic signs), and metallic paint films are
outside the scope of this part of MS 133 : Part D10. This
standard is technically equivalent to ISO 7724/2 : 1984
except for Clause 7 Note : The temperature of the test
specimen at (23 ± 2) °C had
been amended to (27 ± 2) °C. |
|
| Price Code : B | |
| MS 133 : Part D11 : 1999 | |
| Methods of test for paints and varnishes : Part D11 : Colorimetry - calculation of colour differences. | |
| Describes a method for the quantitative colorimetric evaluation of small colour differences between paint films. | |
| Price Code : A | |
| MS 133 : Part E1 : 2000 | |
| Methods of test for paints and varnishes : Part E1 : Bend test (Cylindrical mandrel) (First revision) | |
| Specifies an
empirical test procedure for assessing the resistance of
a coating of paint, varnish or related product to
cracking and/or detachment from a metal substrate when
subjected to bending round a cylindrical mandrel under
standard conditions. This standard supersedes MS 133 :
Part E1 : 1973. |
|
| Price Code : B | |
| MS 133 : Part E2 : 2000 | |
| Methods of test for paints and varnishes : Part E2 : Scratch test (First revision) | |
| Specifies a
test method for determining under defined conditions the
resistance of a single coating or a multi-coat system of
paint, varnish or related product to penetration by
scratching with a hemispherically tipped needle. This
standard supersedes MS 133 : Part E2 : 1973. |
|
| Price Code : B | |
| MS 133 : Part E3 : 2000 | |
| Methods of test for paints and varnishes : Part E3 : Resistance to impact (Falling - Weight test) (First revision) | |
| Specifies a
test method for evaluating the resistance of a dry film
of paint, varnish or related product to cracking or
peeling from a substrate when it is subjected to a
deformation caused by a falling weight, dropped under
standard conditions. This standard supersedes MS 133 :
Part E3 : 1973. |
|
| Price Code : B | |
| MS 133 : Part E4 : 2000 | |
| Methods of test for paints and varnishes : Part E4 : Cupping test (First revision) | |
| Specifies an
empirical test procedure for assessing the resistance of
a coating of paint, varnish or related product to
cracking and/or detachment from a metal substrate when
subjected to gradual deformation by indentation under
standard conditions. This standard supersedes MS 133 :
Part E4 : 1973. |
|
| Price Code : B | |
| MS 133 : Part E5 : 2000 | |
| Methods of test for paints and varnishes : Part E5 : Pendulum damping test (First revision) | |
| Specifies
standard conditions for carrying out a pendulum damping
test on a single coating or a multicoat system of paint,
varnish or related product. This standard supersedes MS
133 : Part E5 : 1978. |
|
| Price Code : B | |
| MS 133 : Part E6 : 2000 | |
| Methods of test for paints and varnishes : Part E6 : Cross-cut test (First revision) | |
| Specifies a
test method for assessing the resistance of paint
coatings to separation from substrates when a right-angle
lattice pattern is cut into the coating, penetrating
through to the substrate. This standard supersedes MS 133
: Part E6 : 1976. |
|
| Price Code : B | |
| MS 133 : Part E7 : 2000 | |
| Methods of test for paints and varnishes : Part E7 : Resistance to impact (Falling ball test) (First revision) | |
| Describes a
procedure for determining the resistance to impact of a
singlecoat or a multicoat system of paints, varnishes, or
related products, using a free falling ball. This
standard supersedes MS 133 : Part E7 : 1980. |
|
| Price Code : A | |
| MS 133 : Part E8 : 2000 | |
| Methods of test for paints and varnishes : Part E8 : Resistance to impact (Pendulum test) | |
| This Malaysian Standard describes a procedure for determining the resistance of a single-coat film or a multicoat system of paints, varnishes or related products to a single-blow impact by a pendulum. | |
| Price Code : A | |
| MS 133 : Part E9 : 2000 | |
| Methods of test for paints and varnishes : Part E9 : Buchholz indentation test | |
| Specifies a
method for carrying out an indentation test on a single
coating or multicoat system of paint, varnishes or
related product, using a specified instrument (Buchholz). |
|
| Price Code : A | |
| MS 133 : Part E10 : 2000 | |
| Methods of test for paints and varnishes : Part E10 : Pull-off test for adhesion | |
| Specifies methods for carrying out a pull-off test on a single coating or a multi-coat system of paint, varnish or related product. | |
| Price Code : B | |
| MS 133 : Part E11 : 2000 | |
| Methods of test for paints and varnishes : Part E11 : Bend test (Conical mandrel) | |
| Describes an empirical test procedure for assessing the resistance of a coating of paint varnish. | |
| Price Code : A | |
| MS 133 : Part E12 : 2000 | |
| Methods of test for paints and varnishes : Part E12 : Indentation test (Spherical or pyramidal) | |
| Describes a test procedure for the conduct of an indentation test on a single or multi-coat system of paint, varnish or related product. | |
| Price Code : A | |
| MS 133 : Part E14 : 2002 | |
| Methods of test for paints and varnishes : Part E14 : Determination of resistance to abrasion (Rotating abrasive-paper-covered wheel) | |
| This Malaysian Standard specifies a method for determining the resistance to abrasion of a dried film of paint, varnish or related product, using abrasive paper attached to wheels and abrading by making a rotary movement. | |
| Price Code : B | |
| MS 133 : Part E15 : 2002 | |
| Methods of test for paints and varnishes : Part E15 : Determination of resistance to abrasion (Rotating abrasive rubber wheel) | |
| This part of Malaysian Standard is one of a series of standards dealing with the sampling and testing of paints, varnishes and related products. This Malaysian Standard specifies a method for determining the resistance to abrasion of a dried film of paint, varnish or related product, using abrasive rubber wheels and abrading by making a rotary movement. | |
| Price Code : B | |
| MS 133 : Part E16 : 2002 | |
| Methods of test for paints and varnishes : Part E16 : Determination of resistance to abrasion (Reciprocating test panel) | |
| This part of Malaysian Standard is one of a series of standards dealing with the sampling and testing of paints, varnishes and related products. It specifies a method of determining the resistance to abrasion of a dried film of paint, varnish or related product by rubbing the film against a strip of abrasive paper attached to a stationary wheel. | |
| Price Code : B | |
| MS 133 : Part E17 : 2002 | |
| Methods of test for paints and varnishes : Part E17 : Determination of mar resistance using a curved stylus | |
| This part of Malaysian Standard is one of a series of standards dealing with the sampling and testing of paints, varnishes and related products. It specifies a method for determining, using a curved (loop-shaped or ring-shaped) stylus, the mar resistance of a single coating of a paint, varnish or related product, or the upper layer of a multi coat system. MS 133 : Part E18 specifies a method using a pointed stylus. The choice between the two methods will depend on the particular practical problem. | |
| Price Code : B | |
| MS 133 : Part E18 : 2002 | |
| Methods of test for paints and varnishes : Part E18 : Determination of mar resistance using a pointed stylus | |
| This part of Malaysian Standard is one of a series of standards dealing with the sampling and testing of paints, varnishes and related products. It specifies a method for determining, using a pointed stylus, the mar resistance of a single coating of a paint, varnish or related product, or the upper layer of a multi coat system. MS 133 : Part E17 specifies a method using a pointed stylus. The choice between the two methods will depend on the particular practical problem. | |
| Price Code : B | |
| MS 133 : Part E19 : 2002 | |
| Methods of test for paints and varnishes : Part E19 : Determination of film hardness by pencil test | |
| This Malaysian Standard is one of a series of standards dealing with the sampling and testing of paints, varnishes and related products. It specifies a method for determining the film hardness by pushing pencils of known hardness over the film. The test can be performed on a single coating of a paint, varnish or related product, or on the upper layer of multi-coat system. | |
| Price Code : B | |
| MS 133 : Part F1 : 1973 | |
| Methods of test for paints : Part F1 : Alkali resistance of plaster primer-sealer. | |
| Describes a procedure for determining the sealing properties of plaster primer-sealer. | |
| Price Code : A | |
| MS 133 : Part F2 : 2002 | |
| Methods of test for paints and varnishes : Part F2 : Resistance to humidity (Continuous condensation) (First revision) | |
| This Malaysian Standard specifies a method for determining the resistance of paint films, paints systems and allied products to conditions of high humidity. The method is applicable to coatings both on porous substrates such as wood, plaster and plasterboard, and on non-porous substrates such as metal. It provides an indication of performance likely to be obtained under severe conditions of exposure where continuous condensation occurs on the surface. The procedure may reveal failures of the coating (including blistering, staining, softening, wrinkling and embrittlement) and deterioration of the substrate. This standard supersedes MS 133 : Part F2 : 1973. | |
| Price Code : A | |
| MS 133 : Part F3 : 1976 | |
| Methods of test for paints : Part F3 : Resistance to artificial weathering (enclosed carbon-arc). | |
| Applicable
to single films or multicoat systems of paints or allied
materials. |
|
| Price Code : B | |
| MS 133 : Part F4 : 1973 | |
| Methods of test for paints : Part F4 : Resistance to continuous salt spray. | |
| Describes a procedure for determining the resistance of single film or multicoat system of paints or allied materials to a continuous salt water (artificial seawater) spray. To be used in conjunction with MS 133. | |
| Price Code : B | |
| MS 133 : Part F5 : 1975 | |
| Methods of test for paints : Part F5 : Determination of light fastness of paints for interior use exposed to artificial light sources. | |
| Alternative
type of apparatus permitted, based on arc or a xenon arc
as light source. |
|
| Price Code : B | |
| MS 133 : Part F6 : 1985 | |
| Methods of test for paints : Part F6 : Resistance to natural weathering. | |
| Test panels
are exposed to the natural weathering at a test site for
the required period and then examined against a reference
panel. |
|
| Price Code : A | |
| MS 133 : Part F7 : 1978 | |
| Methods of test for paints : Part F7 : Determination of resistance to water (water immersion method). | |
| Methods
confined to conditions where prolonged condensation may
be produced but not an extremely corrosive atmosphere. |
|
| Price Code : A | |
| MS 133 : Part F8 : 1986 | |
| Methods of test for paints : Part F8 : Resistance to accelerated weathering, xenon arc method. | |
| Method
specifies a xenotest 150 apparatus or equivalent. |
|
| Price Code : A | |
| MS 133 : Part F9 : 1986 | |
| Methods of test for paints : Part F9 : Washability. | |
| Describes a
procedure for determining the washability of latex
emulsion paints. It involves the removal of a pencil
stain from the paint film using warm soap solution. |
|
| Price Code : A | |
| MS 133 : Part F10 : 2003 | |
| Methods of test for paints and varnishes: Part F10: Determination of resistance to cathodic disbonding of coatings for use in marine environments. | |
| This
Malaysian Standard describes a method of test for
determining the resistance to cathodic disbonding of a
single coating or multi-coat system of paint, varnish or
other organic coating applied to metallic substrates when
the surface coating covering the metal substrate may
contain or develop discontinuities. It is applicable to
coatings that are subjected to marine environments, such
as those on ships or partially exposed marine structures.
NOTES: For coatings that are used to protect land-based
metallic structures, the conditions of the test differ
from those for coatings to be used in marine
applications. MS 133: Part F11 describes a method
suitable for assessing coatings applied to buried
structures. The test result may be influenced not only by
the properties of the coating system under test, but also
by the nature and preparation of the substrate, the
method of application of the coating system and other
factors. |
|
| Price Code : B | |
| MS 133 : Part F11 : 2003 | |
| Methods of test for paints and varnishes: Part F11: Determination of resistance to cathodic disbonding of coatings for use in land-based buried structures. | |
| This
Malaysian Standard describes a method of test for
determining the resistance to cathodic disbonding of a
single coating or multi-coat system of paint, varnish or
other organic coating applied to metallic substrates when
the surface coating covering the metal substrate may
contain or develop discontinuities. It is applicable to
coatings that are to be applied to land-based structures,
such as buried pipelines. NOTES: 1. For coatings that are
to be used in marine environments on ships or partially
exposed marine structures, the conditions of the test
differ from those for coatings to be used in land-based
applications. MS 133: Part F10 describes a method
suitable for assessing coatings applied to marine
structures. 2. The test result may be influenced not only
by the properties of the coating system under test, but
also by the nature and preparation of the substrate, the
method of application of the coating system and other
factors. |
|
| Price Code : B | |
| MS 133 : Part F12 : 2003 | |
| Methods of test for paints and varnishes: Part F12: Determination of resistance to neutral salt spray (Fog). | |
| This
Malaysian Standard is one of a series of standards
dealing with the sampling and testing of paints,
varnishes and related products. It describes a method for
determining the resistance of coatings to neutral salt
spray (fog) in accordance with the requirements of
coating or product specifications. |
|
| Price Code : B | |
| MS 133 : Part F13 : 2003 | |
| Methods of test for paints and varnishes: Part F13: Determination of resistance to filiform corrosion on steel substrates. | |
| This
Malaysian Standard is one of a series of standards
dealing with the sampling and testing of paints,
varnishes and related products. It describes a test
procedure for assessing the protective action of coatings
of paints or varnishes on steel against filiform
corrosion arising from a scribed mark cut through the
coating. |
|
| Price Code : B | |
| MS 133 : Part F14 : 2003 | |
| Methods of test for paints and varnishes: Part F14: Artificial weathering and exposure to artificial radiation- Exposure to filtered xenon-arc radition. | |
| This
Malaysian Standard is one of a series of standards
dealing with the sampling and testing of paints,
varnishes and related products. It specifies a test
method for assessing either the resistance of paint
coatings to artificial weathering or the resistance to
light by exposure to artificial radiation. The standard
describes the most important parameters and specifies the
conditions to be used in the exposure apparatus. Provided
the test conditions specified are strictly respected,
reproducibility is improved and an improved correlation
is obtained between natural-weathering and
artificial-weathering tests. |
|
| Price Code : B | |
| MS 133 : Part F15 : 2003 | |
| Methods of test for paints and varnishes: Part F15: Determination of resistance to humidity (intermittent condensation). | |
| This
Malaysian Standard is one of a series of standards
dealing with the sampling and testing of paints,
varnishes and related products. It specifies a test
method for determining under standard conditions the
resistance of a single coat or a multi-coat system of
paint or related material to intermittent water
condensation. The method includes the testing of coatings
on non-porous and on porous substrates. |
|
| Price Code : B | |
| MS 133 : Part F16 : 2003 | |
| Methods of test for paints and varnishes: Part F16: Exposure of coatings to artificial weathering-exposure to fluorescent UV and water. | |
| This
Malaysian Standard is one of a series of standards
dealing with the sampling and testing of paints,
varnishes and related products. It specifies a test
method for determining the resistance of paint coatings
to artificial weathering in apparatus including
fluorescent UV lamps and condensation or water spray.
NOTE. The ultraviolet light produced by the fluorescent
tubes simulates only part of the UV region of the natural
sunlight and consequently the test pieces are subjected
to a small but destructive portion of the spectrum. Due
to the lack of energy of visible and infra-red radiation
compared to sunlight the test piece is not heated above
the temperature of the surrounding air which takes place
in practical use. |
|
| Price Code : A | |
| MS 133 : Part F17 : 2003 | |
| Methods of test for paints and varnishes: Part F17: Determination of wet-scrub resistance and cleanability of coatings. | |
| The ability
of coatings to withstand wear caused by repeated cleaning
operations and to resist permanent blemishing by stains
is an important consideration both from a practical point
of view and when comparing and rating such coatings. This
Malaysian Standard specifies an accelerated method for
the determination of wet-scrub resistance. With regard to
the cleanability of coatings, only the method itself and
not the soiling agents are specified. NOTE. Since these
properties depend not only on the quality of a coating
but also on the substrate, the method of application, the
drying conditions and other factors, the results obtained
are not directly transferable to actual practice. In this
standard the evaluation of the coating is based on a
defined substrate, a fixed application method, specified
drying conditions and a defined method of wet scrubbing. |
|
| Price Code : B | |
| MS 133 : Part F18 : 2003 | |
| Methods of test for paints and varnishes: Part F18: Determination of resistance to corrosion under a wet (salt fog)/dry/humidity cycle. | |
| This
Malaysian Standard is one of a series of standards
dealing with the sampling and testing of paints,
varnishes and related products. It specifies a method of
determining the resistance of coatings to one of three
defined cycles of wet (salt fog)/dry/humidity conditions
using specified solutions. |
|
| Price Code : B | |
| MS 133 : Part G1 : 1973 | |
| Methods of test for paints : Part G1 : Resistance to organic liquids | |
| Describes a general procedure for determining the resistance of single films or systems of film of paints or allied materials to the action of organic liquids like alcohols, esters, ketones, hydraulic oils, paint solvent, petroleum synthetic lubricant and vegetable oils. To be used in conjunction with MS 13 | |
| Price Code : A | |
| MS 133 : Part G2 : 1973 | |
| Methods of test for paints : Part G2 : Resistance to aqueous liquids | |
| Describes a general procedure for determining the resistance of single films or systems of films of paints or allied materials to the action of single phase aquaeous liquids and two-phase liquids with or without aeration. To be used in conjunction with MS 133 | |
| Price Code : A | |
| MS 133 : Part G3 : 1973 | |
| Methods of test for paints : Part G3 : Resistance to spotting by liquids | |
| Describes a general procedure for determining the resistance of single films or systems of films of paints or allied materials to the spotting by liquids such as can result from accidental splashing. To be used in conjunction with MS 133. | |
| Price Code : A | |
| MS 133 : Part G4 : 1973 | |
| Methods of test for paints : Part G4 : Resistance to hot fats | |
| Describes a general procedure for determining the resistance of single films or systems of films or allied materials to the action of hot fats. To be used in conjunction with MS 133. | |
| Price Code : A | |
| MS 133 : Part G5 : 1975 | |
| Methods of test for paints : Part G5 : Resistance to liquids | |
| Describes a general procedure for determining the resistance of single films or multicoat systems of paints or allied materials to the action of single phase liquids (with or without aeration, agitation or circulation) or to two-phase liquids. To be used in conjunction with MS 133. | |
| Price Code : B | |
| MS 133 : Part G6 : 1978 | |
| Methods of test for paints : Part G6 : Resistance to fungal growth. | |
| Assesses the
resistance of paints containing fungicides to mold growth
under conditions of elevated temperature and humidity. |
|
| Price Code : A | |
| MS 133 : Part H1 : 1987 | |
| Methods of test for paints : Part H1 : Rating schemes for evaluation of degradation of paint coatings. | |
| Establishes
a general scheme for designating the quality and size of
common types of defects of paint coatings. |
|
| Price Code : A | |
| MS 133 : Part H2 : 1987 | |
| Methods of test for paints : Part H2 : Evaluation of degree of blistering. | |
| Provides
pictorial standards for evaluating the degree of
blistering of paint coatings. |
|
| Price Code : A | |
| MS 133 : Part H3 : 1989 | |
| Methods of test for paints : Part H3 : Evaluation of degree of rusting. | |
| Provides
pictorial standards for evaluating the degree of rusting
of paint coatings. |
|
| Price Code : A | |
| MS 133 : Part H4 : 1987 | |
| Methods of test for paints : Part H4 : Evaluation of degree of cracking. | |
| Provides
pictorial standards for evaluating the degree of cracking
of paint coatings. |
|
| Price Code : A | |
| MS 133 : Part H5 : 1987 | |
| Methods of test for paints : Part H5 : Evaluation of degree of flaking. | |
| Provides
pictorial standards for evaluating the degree of flaking
of paint coatings. |
|
| Price Code : A | |
| MS 134 : 1989 | |
| Specification for latex emulsion paint for exterior and interior use (Second revision). | |
| Specifies an
air-drying latex emulsion paint for both exterior or
interior use on masonary surfaces including concrete,
brick, stucco concrete block and asbestos-cement shingles
and slidings. Requirements include nonvolatile content,
consistency, fineness of grind, opacity, drying time and
resistance to weathering and fungal growth. |
|
| Price Code : A | |
| MS 162 : 1987 | |
| Specification for aluminium wood primer (First revision). | |
| Specifies
requirements such as pigment, vehicle non-volatile
matter, flash point, storage properties, drying time, and
flexibility and adhersion. |
|
| Price Code : A | |
| MS 163 : 1973 | |
| Specification for water paint/distemper, washable oil bound. | |
| Specifies
requirements such as pigment, vehicle non-volatile
matter, storage properties, drying time, application
properties and washability. |
|
| Price Code : B | |
| MS 164 : 1991 | |
| Specification for road marking paints (Second revision). | |
| Covers two
types: Type I chlorinated rubber base abd Type II
One-pack epoxy. Paint may be non-reflective or
reflective. Requirements include non-volatile matter,
consistency, drying time, fineness of grind, opacity,
luminance factor, application properties, resistance to
abrasion bleeding, weathering, and flexibility and
adhesion. |
|
| Price Code : B | |
| MS 270 : 1975 | |
| Specification for priming paint : Red lead based for iron and steel. | |
| Classified
into three types in accordance to drying time. For use as
a primer on prepared iron and steel surfaces under indoor
and outdoor weather conditions. |
|
| Price Code : A | |
| MS 271 : 1993 | |
| Specification for red iron oxide primer (First revision). | |
| This Malaysian Standard is a first revision of the MS 271 : 1975, "Specification for priming paint : Red oxides for iron and steel". This standard specifies the composition and requirements for red iron oxide based paint for use as a primer on iron and steel surfaces under indoor and outdoor weather conditions. | |
| Price Code : A | |
| MS 272 : 1975 | |
| Specification for priming paint : Zinc chromate for metal surfaces. | |
| Specifies
description, composition, properties and methods of test.
For use on prepared ferrous and non-ferrous surfaces
under indoor and outdoor weather conditions. |
|
| Price Code : B | |
| MS 288 : 1975 | |
| Specification for paint, dry, cementitious (cement paint). | |
| Specifies
description,sampling, composition, requirements, packing
and test methods. For use on porous surfaces as a
decorative and protective coating. |
|
| Price Code : C | |
| MS 289 : 1987 | |
| Specification for aluminium finishing paint (First revision). | |
| For use on
primed interior and exterior wood and metal surfaces, and
for recoating of previously painted surfaces, provided
the surface is in sound condition and suitable for
receiving such a coating. |
|
| Price Code : A | |
| MS 291 : 1984 | |
| Specification for paint remover, solvent type, non-flammable. | |
| For use on
finished wood and metal surfaces. Storage properties,
efficiency, acidity, alkalinity, inflammability,
consistency effects on wood and steel are prescribed. |
|
| Price Code : B | |
| MS 903 : 1984 | |
| Specification for latex emulsion paint for interior use. | |
| Requirements
are given for non volatile matter content, consistency,
specific gravity, fineness of grind, opacity, drying
time, redispersion, storage stability, application
properties and appearance washability, fastness to
artificial light and resistance to fungal growth.
Procedures for packing, marking, sampling and methods of
test are included. |
|
| Price Code : A | |
| MS 1327 : 1993 | |
| Specification for zinc phosphate primer. | |
| This
Malaysian Standard specifies the composition and
requirements for zinc phosphate primer for use on ferrous
and non-ferrous surfaces under indoor and outdoor weather
conditions. This standard was based on verified
information from the paint industry and also findings
from extensive testing conducted on zinc phosphate
samples manufactured locally. |
|
| Price Code : A | |
| MS 1431: 1998 | |
| Paints and varnishes : Preparation of acid extracts from paints in liquid or powder form. | |
| This
Malaysian standard describes methods for the preparation
of acid extracts required as the test solutions for the
determination of the "soluble" metal contents
of paints and related products in liquid or powder form.
The acid extracts are prepared in 0.07 mol/l hydrochloric
acids, which is chosen as an approximation of the acid in
the stomach. |
|
| Price Code : B | |
Paint ingredients |
|
Pigments and extenders |
|
| MS 11 : 1971 | |
| Specification for antimony oxide for paint. | |
| Specifies
requirements including appearance and composition for
antimony oxide intended for use as a paint pigment. |
|
| Price Code : A | |
| MS 12 : 1971 | |
| Specification for titanium dioxide for paints. | |
| Specifies
requirements for titanium dioxide rutile for use as
pigments in the paint industry. The zinc reduction and
the aluminium reduction methods for determination of
titanium dioxide content are given as the method that
determines resistance to chalking. |
|
| Price Code : B | |
Solvents |
|
| MS 905 : 1984 | |
| Specification for white spirit for paints and other purposes. | |
| This
standard specifies the requirements for white spirit
(also known as mineral turpentine or Stoddard solvent)
with an aromatic content of 15% to 25% (v/v) for use in
paints and varnishes and, for other purposes. |
|
| Price Code : B | |
Inks. Printing inks |
|
| MS 430 : 1976 (1985) | |
| Specification for ink paste, black (stencil, duplicating-machine). | |
| Covers
requirements for two classes of ink:Class A: For use on
single-cylinder (drum type) internally inked machine.
Class B:For use on dual-cylinder externally linked
machines. |
|
| Price Code : B | |
| MS ISO 2836 : 2001 | |
| Graphic technology - Prints and printing links - Assessment of resistance to various agents | |
| This Malaysian Standard specifies methods for assessing the resistance of prints and printing inks to water, alkalis, oils and fats, cheese, detergents, soaps, wax and spices. It applies to all printing substrates such as paper, board, metals (thin metal sheet and plate) and plastic materials and to all printing processes, e.g. lithographic, gravure, letterpress, flexo, screen and non-impact printing. | |
| Price Code : A | |
| MS ISO 2837 : 2003 | |
| Graphic technology -
Prints and printing inks - Assessment of resistance to
solvents |
|
| This Malaysian Standard
specifies a method of assessing the resistance of prints
and printing inks to solvents. |
|
| Price RM10 | |
| |
|