NEWLY PUBLISHED MALAYSIAN STANDARDS - MAY 2010
01. Generalities. Terminology.
Standardization
MS ISO 6107-1 : 2010
- Water quality - Vocabulary - Part 1 (First revision) (RM20) (ICS
13.060.01 / 01.040.13)
MS ISO 6107-2 : 2010 - Water quality - Vocabulary - Part 2 (First
revision) (RM30) (ICS 13.060.01 / 01.040.13)
MS ISO 6107-5 : 2010 - Water quality - Vocabulary - Part 5 (First
revision) (RM20) (ICS 13.060.01 / 01.040.13)
MS ISO 6107-6 : 2010 - Water quality - Vocabulary - Part 6 (First
revision) (RM20) (ICS 13.060.01 / 01.040.13)
MS ISO 6107-7 : 2010 - Water quality - Vocabulary - Part 7 (First
revision) (RM20) (ICS 13.060.01 / 01.040.13)
MS ISO 18369-1 : 2009 - Ophthalmic optics - Contact
lenses - Part 1 : Vocabulary, classification system and
recommendations for labelling specifications (RM320) (ICS
01.040.11 / 11.040.70)
03. Sociology. Services. Company Organization and Management.
Administration. Transport
MS ISO 8422 : 2010 - Sequential sampling plans for inspection by
attributes (First revision) (RM260) (ICS 03.120.30)
MS ISO 8423 : 2010 - Sequential sampling plans for inspection by
variables for percent nonconforming (known standard deviation)
(First revision) (RM260) (ICS 03.120.30)
11. Health Care Technology
MS 2272-1 : 2010 - Sterile hypodermic syringes for single use -
Part 1 : Syringes for manual use (RM40) (ICS 11.040.25)
MS ISO 8835-2 : 2010 - Inhalational anaesthesia systems - Part 2
: Anaesthetic breathing systems (RM230) (ICS 11.040.10)
MS ISO 8835-3 : 2010 - Inhalational anaesthesia systems - Part 3
: Transfer and receiving systems of active anaesthetic gas
scavenging systems (RM300) (ICS 11.040.10)
MS ISO 9170-1 : 2010 - Terminal units for medical gas pipeline
systems - Part 1 : Terminal units for use with compressed medical
gases and vacuum (First revision) (RM210) (ICS 11.040.10)
MS ISO 9170-2 : 2010 - Terminal units for medical gas pipeline
systems - Part 2 : Terminal units for anaesthetic gas scavenging
systems (First revision) (RM230) (ICS 11.040.10)
MS ISO 13779-3 : 2010 - Implants for surgery - Hydroxyapatite -
Part 3 : Chemical analysis and characterization of crystallinity
and phase purity (RM210) (ICS 11.040.40)
MS ISO 13779-4 : 2010 - Implants for surgery - Hydroxyapatite -
Part 4 : Determination of coating adhesion strength (RM130)
(ICS 11.040.40)
MS ISO 18369-1 : 2009 - Ophthalmic optics - Contact lenses - Part
1 : Vocabulary, classification system and recommendations for
labelling specifications (RM320) (ICS 01.040.11 / 11.040.70)
MS ISO 22442-1 : 2010 - Medical devices utilizing animal
tissues and their derivatives - Part 1 : Appication of risk
management (RM240) (ICS 11.100.20)
MS ISO 22442-2 : 2010 - Medical devices utilizing animal
tissues and their derivatives - Part 2 : Controls on sourcing,
collection and handling (RM180) (ICS 11.100.20)
MS ISO 22442-3 : 2010 - Medical devices utilizing animal
tissues and their derivatives - Part 3 : Validation of the
elimination and/or inactivation of viruses and transmissible
spongiform encephalopathy (TSE) agents (RM230) (ICS
11.100.20)
13. Environment. Health
Protection. Safety
MS 1597-2-35 : 2010
- Household and similar electrical appliances - Safety - Part
2-35 : Particular requirements for instantaneous water heaters
(Second revision) (RM30) (ICS 13.120 / 97.040.50)
MS 1597-2-80 : 2010 - Household and similar electrical appliances
- Safety - Part 2-80 : Particular requirements for fans (Third
revision) (RM20) (ICS 13.120 / 97.040.50)
MS 2226 : 2009 - Magnetic resonance imaging - Code of practice
for safety (RM80) (ICS 13.280 / 17.140 / 17.240)
MS 61508-1 : 2010 - Functional safety of
electrical/electronic/programmable electronic safety-related
systems - Part 1 : General requirements (RM60) (ICS
13.110 / 25.040 / 29.020)
MS ISO 1503 : 2010 - Spatial orientation and direction of
movement - Ergonomic requirements (RM50) (ICS 13.180)
MS ISO 6107-1 : 2010 - Water quality - Vocabulary - Part 1 (First
revision) (RM20) (ICS 13.060.01 / 01.040.13)
MS ISO 6107-2 : 2010 - Water quality - Vocabulary - Part 2 (First
revision) (RM30) (ICS 13.060.01 / 01.040.13)
MS ISO 6107-5 : 2010 - Water quality - Vocabulary - Part 5 (First
revision) (RM20) (ICS 13.060.01 / 01.040.13)
MS ISO 6107-6 : 2010 - Water quality - Vocabulary - Part 6 (First
revision) (RM20) (ICS 13.060.01 / 01.040.13)
MS ISO 6107-7 : 2010 - Water quality - Vocabulary - Part 7 (First
revision) (RM20) (ICS 13.060.01 / 01.040.13)
MS ISO 4642-1 : 2010 - Rubber and thermoplastics hoses,
non-collapsible, for fire-fighting service - Part 1 : Semi-rigid
hoses for fixed systems (First revision) (RM30) (ICS
13.220.10 / 83.140.40)
MS ISO 4642-2 : 2010 - Rubber and thermoplastics hoses,
non-collapsible, for fire-fighting service - Part 2 : Semi-rigid
hoses (and hose assemblies) for pumps and vehicles (First
revision) (RM40) (ICS 13.220.10 / 83.140.40)
MS ISO 9241-20 : 2010 - Ergonomics of human-system interaction -
Part 20 : Accessibility guidelines for information/communication
technology (ICT) equipment and services (RM50) (ICS
13.180 / 35.180)
MS ISO 13856-2 : 2006 - Safety of machinery - Pressure-sensitive
protective devices - Part 2 : General principles for the design
and testing of pressure-sensitive edges and pressure-sensitive
bars (RM330) (ICS 13.110)
MS ISO 14956 : 2010 - Air quality - Evaluation of the suitable of
a measurement procedure by comparison with a required measurement
uncertainty (RM40) (ICS 13.040.01)
MS ISO 16000-7 : 2009 - Indoor air - Part 7 : Sampling strategy
for determination of airborne asbestos fibre concentrations
(RM20) (ICS 13.040.20)
MS ISO 16000-12 : 2009 - Indoor air - Part 12 : Sampling
strategy for polychlorinated biphenyls (PCBs), polychlorinated
dibenzo-p-dioxins
(PCCDs), polychlorinated dibenzofurans (PCDFs) and polycyclic
aromatic hydrocarbons (PAHs) (RM40) (ICS 13.040.20)
MS ISO 19353 : 2006 - Safety of machinery - Fire prevention
and protection (RM210) (ICS 13.110)
MS ISO 29042-3 : 2010 - Safety of machinery - Evaluation of the
emission of airborne hazardous substances - Part 3 : Test bench
method for the measurement of the emission rate of a given
pollutant (RM130) (ICS 13.110)
17. Metrology
and Measurement. Physical Phenomena
MS 2226 : 2009 - Magnetic resonance imaging - Code of practice
for safety (RM80) (ICS 13.280 / 17.140 / 17.240)
MS ISO/ASTM 51205 : 2009
- Practice for use of a ceric-cerous sulfate dosimetry system
(RM160) (ICS 17.240)
19. Testing
MS IEC 60068-2-65 : 2010
- Environmental testing - Part 2-65 : Methods of tests - Test FG
: Vibration, acoustically induced (RM290) (ICS 19.040)
MS IEC 60068-2-77 : 2010 - Environmental testing - Part 2-77 :
Tests - Test 77 : Body strength and impact shock (RM120) (ICS
19.040 / 31.190)
MS IEC 60068-2-81 : 2010 - Environmental testing - Part 2-81 :
Tests - Test EI : Shock - Shock respoense spectrum synthesis
(RM350) (ICS 19.040 )
21 Mechanical Systems and Components for
General Use
MS ISO 3269 : 2010 -
Fasteners - Acceptance inspection (RM200) (ICS 21.060.01)
MS ISO 10683 : 2010 - Fasteners - Non-electrolytically applied
zinc flake coatings (RM140) (ICS 21.060.01 / 25.220.40)
MS ISO 15330 : 2010 - Fasteners - Preloading test for the
detection of hydrogen embrittlement - Parallel bearing surface
method (RM140) (ICS 21.060.01)
23. Fluid Systems and
Components for General Use
MS 2250 : 2009 -
Thermoplastics piping systems - Non-end-load-bearing elastomeric
sealing ring type joints between pressure pipes and moulded
fittings - Test method for leaktightness under internal
hydrostatic pressure without end thrust (RM10) (ICS 23.020)
MS 2251 : 2009 - Plastics piping systems - Injection-moulded
thermoplastics fittings for elastic sealing ring type joints for
pressure piping - Test method for resistance to a short-term
internal pressure without end thrust (RM10) (ICS 23.020)
MS 2252 : 2009 - Plastics piping systems - Injection-moulded
socket fittings for solvent-cemented joints for pressure piping -
Test method for resistance to a short-term internal hydrostatic
pressure (RM10) (ICS 23.020)
MS 2286-1 : 2010 - Plastics piping systems for hot and cold water
installations - Polypropylene (PP) - Part 1 : General (RM20)
(ICS 23.040 / 91.140.60)
MS ISO 10508 : 2009 - Plastics piping sytems for hot and cold
water installations - Guidance for classification and design
(First revision) (RM20) (ICS 23.040.20 / 23.040.45 /
91.140.60)
MS ISO 10931 : 2010 - Plastics piping systems for
industrial applications - Poly (vinylidene fluoride) (PVDF) -
Specifications for components and the system (RM280)
(ICS 23.040.01)
25. Manufacturing Engineering
MS 61508-1 : 2010 - Functional safety of
electrical/electronic/programmable electronic safety-related
systems - Part 1 : General requirements (RM60) (ICS
13.110 / 25.040 / 29.020)
MS 61508-3 : 2010 -
Functional safety of electrical/electronic/programmable
electronic safety-related systems - Part 3 : Software
requirements (RM50) (25.040)
MS 61508-4 : 2010 -
Functional safety of electrical/electronic/programmable
electronic safety-related systems - Part 4 : Definitions and
abbreviations (RM30) (25.040 / 29.020)
MS 61508-5 : 2010 -
Functional safety of electrical/electronic/programmable
electronic safety-related systems - Part 5 : Examples of methods
for the determination of safety integrity levels (RM40)
(25.040.40)
MS 61508-6 : 2010 -
Functional safety of electrical/electronic/programmable
electronic safety-related systems - Part 6 : Guidelines on the
application of IEC 61508-2 and IEC 61508-3 (RM80)
(25.040.40)
MS 61508-7 : 2010 -
Functional safety of electrical/electronic/programmable
electronic safety-related systems - Part 7 : Overview of
techniques and measures (RM120) (25.040.40 / 35.240.50)
MS IEC 60745-2-3 : 2010 - Hand-held motor-operated
electric tools - Safety - Part 2-3 : Particular requirements for
grinders, polishers and disk-type sanders (First revision) (RM40)
(ICS 25.140.20 / 25.140.30)
MS IEC 60745-2-5 : 2010 - Hand-held motor-operated electric tools
- Safety - Part 2-5 : Particular requirements for circular saws
(First revision) (RM50) (ICS 25.140.20 / 25.140.30)
MS ISO 10683 : 2010 - Fasteners - Non-electrolytically applied
zinc flake coatings (RM140) (ICS 21.060.01 / 25.220.40)
27. Energy and Heat Transfer Engineering
MS 62257-5 : 2009 -
Recommendations for small renewable energy and hybrid systems for
rural electrification - Part 5 : Protection against electrical
hazards (RM40) (ICS 27.160 / 27.180)
MS 62257-6 : 2009 - Recommendations for small renewable energy
and hybrid systems for rural electrification - Part 6 :
Acceptance, operation, maintenance and replacement (RM20) (ICS
27.160 / 27.180)
29. Electrical Engineering
MS 61386-21 : 2010 - Conduit systems for cable
management - Part 21 : Particular requirements - Rigid conduit
systems (First revision) (RM20) (ICS 29.120.10)
MS 61386-22 : 2010 - Conduit systems for cable management - Part
22 : Particular requirements - Pliable conduit systems (First
revision) (RM20) (ICS 29.120.10)
MS 61386-23 : 2010 - Conduit systems for cable management - Part
23 : Particular requirements - Flexible conduit systems (First
revision) (RM20) (ICS 29.120.10)
MS 61386-24 : 2010 - Conduit systems for cable management - Part
24 : Particular requirements - Conduit systems buried underground
(First revision) (RM20) (ICS 29.120.10)
MS 61508-1 : 2010 - Functional safety of
electrical/electronic/programmable electronic safety-related
systems - Part 1 : General requirements (RM60) (ICS
13.110 / 25.040 / 29.020)
MS 61508-4 : 2010 - Functional safety of
electrical/electronic/programmable electronic safety-related
systems - Part 4 : Definitions and abbreviations (RM30)
(25.040 / 29.020)
MS IEC 60320-2-1 : 2010 - Appliance couplers for household and
similar general purposes - Part 2-1 : Sewing machine couplers
(RM20) (ICS 29.120.30)
MS IEC 60320-2-3 : 2010 - Appliance couplers for household and
similar general purposes - Part 2-3 : Appliance couplers with a
degree of protection higher than IPX0 (RM40) (ICS 29.120.30)
MS IEC 60320-2-4 : 2010 - Appliance couplers for household and
similar general purposes - Part 2-4 : Couplers dependent on
appliance weight for engagement (RM30) (ICS 29.120.30)
MS IEC 61386-1 : 2010 - Conduit systems for cable management -
Part 1 : General requirements (First revision) (RM350) (ICS
29.120.10)
31. Electronics
MS IEC 60068-2-77 :
2010 - Environmental testing - Part 2-77 : Tests - Test 77 : Body
strength and impact shock (RM120) (ICS 19.040 / 31.190)
33. Telecommunications. Audio and Video Engineering
MS 62053-61 : 2009 - Electricity metering equipment (a.c.) -
Particular requirements - Part 61 : Power consumption and voltage
requirements (Second revision) (RM10) (ICS 33.200)
MS IEC 61000-4-4 : 2009 - Electromagnetic compatibility (EMC) -
Part 4-4 : Testing and measurement techniques - Electrical fast
transient / burst immunity test (First revision) (RM300) (ICS
33.100.20)
MS IEC 61000-6-1 : 2009 - Electromagnetic compatibility (EMC) -
Part 6-1 : Generic standards - Immunity for residential,
commercial and light-industrial environments (First revision)
(RM160) (ICS 33.100.20)
MS IEC 61000-6-2 : 2009 - Electromagnetic compatibility (EMC) -
Part 6-2 : Generic standards - Immunity for industrial
environments (First revision) (RM140) (ICS 33.100.20)
35. Information
Technology. Office Machines
MS 61508-7 : 2010 - Functional safety of
electrical/electronic/programmable electronic safety-related
systems - Part 7 : Overview of techniques and measures (RM120)
(25.040.40 / 35.240.50)
MS ISO 9241-20 : 2010 - Ergonomics of human-system
interaction - Part 20 : Accessibility guidelines for
information/communication technology (ICT) equipment and services
(RM50) (ICS 13.180 / 35.180)
MS ISO/IEC 11770-2 : 2010 - Information technology - Security
techniques - Key management - Part 2 : Mechanisms using symmetric
techniques (RM40) (ICS 35.040)
MS ISO/IEC 11770-3 : 2010 - Information technology - Security
techniques - Key management - Part 3 : Mechanisms using
asymmetric techniques (RM100) (ICS 35.040)
MS ISO/IEC 18028-2 : 2008 - Information technology - Security
techniques - IT network security - Part 2 : Network security
architecture (RM230) (ICS 35.040)
MS ISO/IEC 13818-1 : 2009
- Information technology - Generic coding of moving pictures and
associated audio information : Systems (RM500) (ICS 35.040)
MS ISO/IEC 13818-4 : 2009 - Information technology - Generic
coding of moving pictures and associated audio information - Part
4 : Conformance testing (RM440) (ICS 35.040)
MS ISO/IEC 15444-2 : 2010 - Information technology - JPEG 2000
image coding system - Part 2 : Extensions (RM650) (ICS
35.040)
MS ISO/IEC 15444-3 : 2010
- Information technology - JPEG 2000 image coding system - Part 3
: Motion JPEG 2000 (RM260) (ICS 35.040)
MS ISO/IEC 15444-4 : 2010
- Information technology - JPEG 2000 image coding system - Part 4
: Conformance testing (RM290) (ICS 35.040)
MS ISO/IEC 27011 : 2010 -
Information technology - Security techniques - Information
security management guidelines for telecommunications
organizations based on ISO/IEC 27002 (RM50) (ICS 35.040)
43. Road Vehicle Engineering
MS ISO 10392 : 2008 -
Road vehicles with two axles - Determination of centre of gravity
(RM110) (ICS 43.020)
MS ISO 14791 : 2008 - Road vehicles - Heavy commercial vehicle
combinations and articulated buses - Lateral stability test
methods (RM240) (ICS 43.080.01)
MS ISO 14792 : 2008 -
Road vehicles - Heavy commercial vehicles and buses -
Steady-state circular tests (RM170) (ICS 43.080.01)
MS ISO 14793 : 2008 -
Road vehicles - Heavy commercial vehicles and buses - Lateral
transient response test methods (RM250) (ICS 43.080.01)
MS ISO 15037-2 : 2008 -
Road vehicles - Vehicle dynamics test methods - Part 2 : General
conditions for heavy vehicles and buses (RM200) (ICS
43.080.01)
MS ISO 16333 : 2008 -
Heavy commercial vehicles and buses - Steady-state rollover
threshold - Tilt-table test method (RM200) (ICS 43.080.01)
MS ISO 21848 : 2010 -
Road vehicles - Electrical and electronic equipment for a supply
voltage of 42 V - Electrical loads (RM170) (ICS 43.040.10)
MS ISO 22902-1 : 2010 - Road vehicles - Automotive multimedia
interface - Part 1 : General technical overview (RM250) (ICS
43.040.15)
59. Textile and Leather Technology
MS ISO 1833-1 : 2010 -
Textiles - Quantitative chemical analysis - Part 1 : General
principles of testing (First revision) (RM30) (ICS 59.060.01)
MS ISO 1833-2 : 2010 - Textiles - Quantitative chemical analysis
- Part 2 : Ternary fibre mixtures (First revision) (RM30) (ICS
59.060.01)
MS ISO 9073-4 : 2010 - Textiles - Test methods for nonwovens -
Part 4 : Determination of tear resistance (RM100) (ICS
59.080.30)
MS ISO 9073-5 : 2010 -
Textiles - Test methods for nonwovens - Part 5 : Determination of
resistance to mechanical penetration (ball burst procedure)
(RM130) (ICS 59.080.30)
MS ISO 9073-6 : 2010 - Textiles - Test methods for nonwovens -
Part 6 : Absorption (RM140) (ICS 59.080.30)
MS ISO 9073-7 : 2010 - Textiles - Test methods for nonwovens -
Part 7 : Determination of bending length (RM110) (ICS
59.080.30)
MS ISO 9073-8 : 2010 - Textiles - Test methods for nonwovens -
Part 8 : Determination of liquid strike-through time (simulated
urine) (RM100) (ICS 59.080.30)
MS ISO 9073-9 : 2010 - Textiles - Test methods for nonwovens -
Part 9 : Determination of drapability including drape coefficient
(RM160) (ICS 59.080.30)
MS ISO 9073-12 : 2010 - Textiles - Test methods for nonwovens -
Part 12 : Demand absorbency (RM160) (ICS 59.080.30)
MS ISO 9073-13 : 2010 - Textiles - Test methods for nonwovens -
Part 13 : Repeated liquid strike-through time (RM130) (ICS
59.080.30)
67. Food Technology
MS 2264 : 2009 - Fat and
oil derivatives - Fatty acid methyl esters (FAME) - Determination
of sodium content by atomic absorption spectrometry (RM20) (ICS
67.200.10)
MS 2265 : 2009 - Fat and oil derivatives - Fatty acid methyl
esters (FAME) - Determination of phosphorus content by
inductively coupled plasma (ICP) emission spectrometry (RM20) (ICS
67.200.10)
MS ISO 5564 : 2008 - Black pepper and white pepper, whole or
ground - Determination of piperine content - Spectrophotometric
method (RM80) (ICS 67.220.10)
MS ISO 6574 : 2008 -
Celery seed (Apium graveolens linnaeus) - Specification (RM100) (ICS
67.220.10)
MS ISO 7543-1 : 2008 - Chillies and chilli oleoresins -
Determination of total capsaicinoid content - Part 1 :
Spectrometric method (RM100) (ICS 67.220.10)
MS ISO 10621 : 2008 - Dehydrated green pepper (Piper nigrum L.) -
Specification (RM100) (ICS 67.220.10)
71. Chemical Technology
MS ISO 1065 : 2010 -
Non-ionic surface-active agents obtained from ethylene oxide and
mixed non-ionic surface-active agents - Determination of cloud
point (RM110) (ICS 71.100.40)
MS ISO 2870 : 2010 - Surface active agents - Detergents -
Determination of anionic-active matter hydrolysable and
non-hydrolysable under acid conditions (RM110) (ICS
71.100.40)
MS ISO 4317 : 2010 - Surface-active agents and detergents -
Determination of water content - Karl Fischer method (RM110) (ICS
71.100.40)
MS ISO 8799 : 2010 -
Surface active agents - Sulfated ethoxylated alcohols and
alkylphenols - Determination of content of unsulfated matter
(RM110) (ICS 71.100.40)
75. Petroleum and Related Technologies
MS 573 : 2009 -
Test method for gage vapor pressure of liquefied petroleum (LP)
gases (LP-gas method) (Second revision) (RM50) (ICS
75.160.30)
MS 2285-1 :
2010 - Petroleum and natural gas industries - Materials for use
in H²S-containing environments in oils and gas production - Part
1 : General principles for selection of cracking-resistant
materials (RM20) (ICS 75.180.01)
MS 2285-2 :
2010 - Petroleum and natural gas industries - Materials for use
in H²S-containing environments in oils and gas production - Part
2 : Cracking-resistant carbon and low alloy steels and the use of
cast irons (RM60) (ICS 75.180.01)
MS 2285-3 :
2010 - Petroleum and natural gas industries - Materials for use
in H²S-containing environments in oils and gas production - Part
3 : Cracking-resistant cras (corrosion-resistant alloys) and
other alloys (RM100) (ICS 75.180.01)
77. Metallurgy
MS 1430 : 2010
- Steel library shelving - Specification (First revision) (RM20) (ICS
77.140)
MS 2240-3 :
2010 - Stainless steels for general purposes - Part 3 : Wire
(RM20) (ICS 77.140.20 / 77.140.65)
83. Rubber and Plastics Industries
MS 1422 : 2009
- Test method for unrestrained linear thermal shrinkage of
plastic film and sheeting (First revision) (RM40) (ICS
83.140.10)
MS 1423 : 2009 - Test method for blocking load of plastic film by
the parallel plate method (First revision) (RM40) (ICS
83.140.10)
MS 1509 : 2009 - Test method for film hardness by pencil test
(First revision) (RM40) (ICS 83.140)
MS ISO 4642-1 :
2010 - Rubber and thermoplastics hoses, non-collapsible, for
fire-fighting service - Part 1 : Semi-rigid hoses for fixed
systems (First revision) (RM30) (ICS 13.220.10 /
83.140.40)
MS ISO 4642-2 : 2010 - Rubber and thermoplastics hoses,
non-collapsible, for fire-fighting service - Part 2 : Semi-rigid
hoses (and hose assemblies) for pumps and vehicles (First
revision) (RM40) (ICS 13.220.10 / 83.140.40)
MS ISO 6914 : 2010 - Rubber, vulcanized or thermoplastic -
Determination of ageing characteristics by measurement of stress
relaxation in tension (First revision) (RM20) (ICS
83.060)
85. Paper Technology
MS ISO 5269-2 :
2010 - Pulps - Preparation of laboratory sheets for physical
testing - Part 2 : Rapid-Kothen method (RM130) (ICS
85.040)
MS ISO 5269-3 : 2010 - Pulps - Preparation of laboratory sheets
for physical testing - Part 3 : Conventional and Rapid-Kothen
sheet formers using a closed water system (RM110) (ICS
85.040)
91. Construction Materials and Building
MS 26-1-8 : 2010 - Testing of concrete - Part 1 : Fresh
concrete - Section 8 : Compacting factor test (Second revision)
(RM10) (ICS 91.100.30)
MS 794 : 2010 - Masonry cement - Specification (First revision)
(RM30) (ICS 91.080.30)
MS 2279 : 2010 - Performance standards in building - Definition
and calculation of area and space indicators (RM30) (ICS
91.040.01)
MS 2280 : 2010 - Aggregates for mortar - Specification (RM30) (ICS
91.100.15)
MS 2281 : 2010 - Clay and calcium silicate bricks of special
shapes and sizes - Recommendations (RM80) (ICS 91.100.15)
MS 2282-3 : 2010 - Masonry units - Specification - Part 3 :
Aggregate concrete masonry units (Dense and light-weight
aggregates) (Second revision) (RM30) (ICS 91.100.30)
MS 2286-1 : 2010 - Plastics piping systems for hot and cold water
installations - Polypropylene (PP) - Part 1 : General (RM20)
(ICS 23.040 / 91.140.60)
MS ISO 10508 : 2009 - Plastics piping sytems for hot and cold
water installations - Guidance for classification and design
(First revision) (RM20) (ICS 23.040.20 / 23.040.45 /
91.140.60)
97. Domestics
and Commercial Equipment. Entertainment. Sports
MS 1597-2-35 : 2010 - Household and similar electrical appliances
- Safety - Part 2-35 : Particular requirements for instantaneous
water heaters (Second revision) (RM30) (ICS 13.120 /
97.040.50)
MS 1597-2-80 : 2010 - Household and similar electrical appliances
- Safety - Part 2-80 : Particular requirements for fans (Third
revision) (RM20) (ICS 13.120 / 97.040.50)