NEWLY PUBLISHED MALAYSIAN STANDARDS - SEPTEMBER 2009
01. Generalities. Terminology.
Standardization
MS 1880-2 : 2009 - Soil
quality - Vocabulary - Part 2 : Terms and definitions relating to
sampling (RM30) (ICS 13.080.01 / 01.040.13)
MS ISO 11979-1 : 2009 - Ophthalmic implants - Intraocular lenses
- Part 1 : Vocabulary (RM140) (ICS 01.040.11 / 11.040.70)
MS ISO 15223-1 : 2009 - Medical devices - Symbols to be used with
medical device labels, labelling and information to be supplied -
Part 1 : General requirements (RM170) (ICS 01.080.20 /
11.040.01)
MS ISO 17115 : 2009 - Health informatics - Vocabulary for
terminological systems (RM160) (ICS 01.040.35 / 35.240.80)
07. Mathematics. Natural Sciences
MS ISO 17713-1 : 2009 -
Meteorology - Wind measurements - Part 1 : Wind tunnel test
methods for rotating anemometer performance (RM30) (ICS
17.080 / 07.060)
MS ISO 17714 : 2009 - Meteorology - Air temperature measurements
- Test methods for comparing the performance of thermometer
shields / screens and defining important characteristics (RM30) (ICS
07.060 / 17.200.20)
11. Health Care Technology
MS 2218 : 2009 - Rubber
condoms - Guidance on the use of MS 113 in the quality management
of natural rubber latex condoms (RM20) (ICS 11.200)
MS IEC 60601-2-33 : 2009 - Medical electrical equipment - Part
2-33 : Particular requirements for the safety of magnetic
resonance equipment for medical diagnosis (RM120) (ICS
11.040.55)
MS IEC 62464-1 : 2009 - Magnetic resonance equipment for medical
imaging - Part 1 : Determination of essential image quality
parameters (RM520) (ICS 11.040.50)
MS ISO 1135-4 : 2009 - Transfusion equipment for medical use -
Part 4 : Transfusion sets for single use (First revision) (RM180)
(ICS 11.040.20)
MS ISO 8536-4 : 2009 - Infusion equipment for medical use - Part
4 : Infusion sets for single use, gravity feed (First revision)
(RM200) (ICS 11.040.20)
MS ISO 11607-1 : 2009 - Packaging for terminally sterilized
medical devices - Part 1 : Requirements for materials, sterile
barrier systems and packaging systems (First revision) (RM240) (ICS
11.080.30)
MS ISO 11607-2 : 2009 - Packaging for terminally sterilized
medical devices - Part 2 : Validation requirements for forming,
sealing and assembly processes (First revision) (RM160) (ICS
11.080.30)
MS ISO 11979-1 : 2009 - Ophthalmic implants - Intraocular lenses
- Part 1 : Vocabulary (RM140) (ICS 01.040.11 / 11.040.70)
MS ISO 11979-3 : 2009 - Ophthalmic implants - Intraocular lenses
- Part 3 : Mechanical properties and test methods (RM260) (ICS
11.040.70)
MS ISO 14971 : 2009 - Medical devices - Application of risk
management to medical devices (First revision) (RM240) (ICS
11.040.01)
MS ISO 15223-1 : 2009 - Medical devices - Symbols to be used with
medical device labels, labelling and information to be supplied -
Part 1 : General requirements (RM170) (ICS 01.080.20 /
11.040.01)
MS ISO 18369-2 : 2009 - Ophthalmic optics - Contact lenses - Part
2 : Tolerances (RM130) (ICS 11.040.70)
MS ISO 18369-3 : 2009 - Ophthalmic optics - Contact lenses - Part
3 : Measurement methods (RM290) (ICS 11.040.70)
MS ISO 18369-4 : 2009 - Ophthalmic optics - Contact lenses - Part
4 : Physicochemical properties of contact lens materials (RM260) (ICS
11.040.70)
13. Environment. Health
Protection. Safety
MS 1745-14 : 2009 - Fire detection and fire alarm systems - Part
14 : Guidelines for planning, design, installation,
commissioning, use and maintenance (RM70) (ICS 13.220.10 /
13.220.20)
MS 1850-14 : 2009 - Water quality - Sampling - Part 14 : Guidance
on quality assurance of environmental water sampling and handling
(RM30) (ICS 13.060.45)
MS 1880-2 : 2009 - Soil quality - Vocabulary - Part 2 : Terms and
definitions relating to sampling (RM30) (ICS 13.080.01 /
01.040.13)
MS IEC 61800-5-2 : 2009 - Adjustable speed electrical power drive
systems - Part 5-2 : Safety requirements - Functional (RM490)
(ICS 29.200 / 13.110)
MS ISO 6182-1 : 2009 - Fire protection - Automatic sprinkler
systems - Part 1 : Requirements and test methods for sprinklers
(First revision) (RM360) (ICS 13.220.20)
MS ISO 6182-2 : 2009 - Fire protection - Automatic sprinkler
systems - Part 2 : Requirements and test methods for wet alarm
valves, retard chambers and water motor alarms (First revision)
(RM230) (ICS 13.220.20)
MS ISO 6182-3 : 2009 - Fire protection - Automatic sprinkler
systems - Part 3 : Requirements and test methods for dry pipe
valves (First revision) (RM210) (ICS 13.220.20)
MS ISO 6182-5 : 2009 -
Fire protection - Automatic sprinkler systems - Part 5 :
Requirements and test methods for deluge valves (First revision)
(RM210) (ICS 13.220.20)
MS ISO 6182-6 : 2009 - Fire protection - Automatic sprinkler
systems - Part 6 : Requirements and test methods for check valves
(RM170) (ICS 13.220.20)
MS ISO 6182-7 : 2009 -
Fire protection - Automatic sprinkler systems - Part 7 :
Requirements and test methods for Early Suppression Fast Response
(ESFR) sprinklers (RM290) (ICS 13.220.20)
MS ISO 6182-8 : 2009 - Fire protection - Automatic sprinkler
systems - Part 8 : Requirements and test methods for pre-action
dry alarm valves (RM230) (ICS 13.220.20)
MS ISO 6182-9 : 2009 - Fire protection - Automatic sprinkler
systems - Part 9 : Requirements and test methods for water mist
nozzles (RM340) (ICS 13.220.20)
MS ISO 6182-10 : 2009 - Fire protection - Automatic sprinkler
systems - Part 10 : Requirements and test methods for domestic
sprinklers (RM170) (ICS 13.220.20)
MS ISO 6182-11 : 2009 -
Fire protection - Automatic sprinkler systems - Part 11 :
Requirements and test methods for pipe hangers (RM170) (ICS
13.220.20)
MS ISO 10780 : 2009 - Stationary source emissions - Measurement
of velocity and volume flowrate of gas streams in ducts (RM30) (ICS
13.040.40)
MS ISO 11564 : 2009 - Stationary source emissions - Determination
of the mass concentration of nitrogen oxides -
Naphthylethylenediamine photometric method (RM30) (ICS
13.040.40)
MS ISO 11632 : 2009 - Stationary source emissions - Determination
of mass concentration of sulfur dioxide - Ion chromatography
method (RM30) (ICS 13.040.40)
MS ISO 12039 : 2009 - Stationary source emissions - Determination
of carbon monoxide, carbon dioxide and oxygen - Performance
characteristics and calibration of automated measuring systems
(RM30) (ICS 13.040.40)
MS ISO 14065 : 2009 - Greenhouse gases - Requirements for
greenhouse gas validation and verification bodies for use in
accreditation or other forms of recognition (RM40) (ICS
13.020.40)
MS ISO 15713 : 2009 - Stationary source emissions - Sampling and
determination of gaseous fluoride content (RM20) (ICS
13.040.40)
17. Metrology and
Measurement. Physical phenomena
MS IEC 62040-2 : 2009 -
Uninterruptible power systems (UPS) - Part 2 : Electromagnetic
compatibility (EMC) requirements (First revision) (RM330) (ICS
33.100.10 / 29.200 / 17.220)
MS ISO 17713-1 : 2009 -
Meteorology - Wind measurements - Part 1 : Wind tunnel test
methods for rotating anemometer performance (RM30) (ICS
17.080 / 07.060)
MS ISO 17714 : 2009 -
Meteorology - Air temperature measurements - Test methods for
comparing the performance of thermometer shields / screens and
defining important characteristics (RM30) (ICS 07.060 /
17.200.20)
19. Testing
MS IEC 61010-2-032 : 2008
- Safety requirements for electrical equipment for measurement,
control and laboratory use - Part 2-032 : Particular requirements
for hand-held and hand-manipulated current sensors for electrical
test and measurement (RM200) (ICS 19.080)
MS IEC 61010-2-081 : 2008 - Safety requirements for electrical
equipment for measurement, control and laboratory use - Part
2-081 : Particular requirements for automatic and semi-automatic
laboratory equipment for analysis and other purposes (RM200) (ICS
19.080 / 71.040.20)
21. Mechanical
Systems and Components for General Use
MS ISO 254 : 2009 - Belt drives - Pulleys - Quality, finish and
balance (RM100) (ICS 21.220.10)
MS ISO 6157-1 : 2009 - Fasteners - Surface
discontinuities - Part 1 : Bolts, screws and studs for general
requirements (RM140) (ICS 21.060.10)
MS ISO 6157-2 : 2009 - Fasteners - Surface
discontinuities - Part 2 : Nuts (RM140) (ICS 21.060.10)
MS ISO 6157-3 : 2009 - Fasteners - Surface
discontinuities - Part 3 : Bolts, screws and studs for special
requirements (RM170) (ICS 21.060.10)
MS ISO 9608 : 2009 - V-belts - Uniformity of belts - Test
method for determination of centre distance variation (RM80) (ICS
21.220.10)
23. Fluid Systems and
Components for General Use
MS 1757 : Part 2 : 2008 - Chlorinated poly (vinyl
chloride) (PVC-C) plastics piping systems - Part 2 :
Specification for schedule 40 pipe fittings (RM20) (ICS
23.040.20)
MS 1757 : Part 3 : 2008 - Chlorinated poly (vinyl chloride)
(PVC-C) plastics piping systems - Part 3 : Specification for
schedule 80 socket-type pipe fittings (RM20) (ICS
23.040.20)
MS ISO 6803 : 2009 - Rubber or thermoplastics hoses and
hose assemblies - Hydraulic - Pressure impulse test without
flexing (RM10) (ICS 23.040.70)
25. Manufacturing Engineering
MS ISO 9455-1 : 2009 -
Soft soldering fluxes - Test methods - Part 1 : Determination of
non-volatile matter, gravimetric method (RM80) (ICS
25.160.50)
MS ISO 9455-2 : 2009 - Soft soldering fluxes - Test methods -
Part 2 : Determination of non-volatile matter, ebulliometric
method (RM1100) (ICS 25.160.50)
MS ISO 9455-3 : 2009 - Soft soldering fluxes - Test methods -
Part 3 : Determination of acid value, potentiometric and visual
titration methods (RM110) (ICS 25.160.50)
MS ISO 9455-5 : 2009 - Soft soldering fluxes - Test methods -
Part 5 : Copper mirror test (RM100) (ICS 25.160.50)
MS ISO 9455-6 : 2009 - Soft soldering fluxes - Test methods -
Part 6 : Determination and detection of halide (excluding
fluoride) content (RM140) (ICS 25.160.50)
MS ISO 9455-8 : 2009 - Soft soldering fluxes - Test methods -
Part 8 : Determination of zinc content (RM80) (ICS 25.160.50)
MS ISO 9455-9 : 2009 - Soft soldering fluxes - Test methods -
Part 9 : Determination of ammonia content (RM100) (ICS
25.160.50)
MS ISO 9455-10 : 2009 - Soft soldering fluxes - Test methods -
Part 10 : Flux efficacy tests, solder spread method (RM140) (ICS
25.160.50)
MS ISO 9455-11 : 2009 - Soft soldering fluxes - Test methods -
Part 11 : Solubility of flux residues (RM100) (ICS 25.160.50)
MS ISO 9455-12 : 2009 - Soft soldering fluxes - Test methods -
Part 12 : Steel tube corrosion test (RM100) (ICS 25.160.50)
MS ISO 9455-13 : 2009 - Soft soldering fluxes - Test methods -
Part 13 : Determination of flux spattering (RM100) (ICS
25.160.50)
MS ISO 9455-14 : 2009 - Soft soldering fluxes - Test methods -
Part 14 : Assessment of tackiness of flux residues (RM100) (ICS
25.160.50)
MS ISO 9455-15 : 2009 - Soft soldering fluxes - Test methods -
Part 15 : Copper corrosion test (RM140) (ICS 25.160.50)
MS ISO 9455-16 : 2009 - Soft soldering fluxes - Test methods -
Part 16 : Flux efficacy tests, wetting balance method (RM200) (ICS
25.160.50)
MS ISO 14171 : 2008 - Welding consumables - Wire electrodes and
wire-flux combinations for submerged arc welding of non alloy and
fine grain steels - Classification (Second revision) (RM170) (ICS
25.160.20)
MS ISO 14341 : 2008 - Welding consumables - Wire electrodes and
deposits for gas shielded metal arc welding of non alloy and fine
grain steels - Classification (Second revision) (RM160) (ICS
25.160.20)
27. Energy and Heat Transfer Engineering
MS CISPR 12 : 2009 -
Vehicles, boats and internal combustion engines - Radio
disturbance characteristics - Limits and methods of measurement
for the protection of off-board receivers (Second revision)
(RM480) (ICS 33.100.10 / 27.020)
MS IEC 61194 : 2009 - Characteristics parameters of stand-alone
photovoltaic (PV) systems (RM140) (ICS 27.160)
MS IEC 62124 : 2009 - Photovoltaic (PV) stand-alone systems -
Design verification (RM330) (ICS 27.160)
29. Electrical Engineering
MS 62102 : 2008 - Electrical safety - Clasification of interfaces
for equipment to be connected to information and communications
technology network (RM30) (ICS 35.020 / 29.020)
MS IEC 60137 : 2009 -
Insulated bushings for alternating voltages above 1000 V (RM420) (ICS
29.080.20)
MS IEC 61800-1 : 2009 - Adjustable speed electrical power drive
systems - Part 1 : General requirements - Rating specifications
for low voltage adjustable speed d.c power drive systems (RM540)
(ICS 29.160.30 / 29.200)
MS IEC 61800-2 : 2009 - Adjustable speed electrical power drive
systems - Part 2 : General requirements - Rating specifications
for low voltage adjustable frequency a.c power drive systems
(RM520) (ICS 29.160.30 / 29.200)
MS IEC 61800-3 : 2009 - Adjustable speed electrical power drive
systems - Part 3 : EMC requirements and specific test methods
(First revision) (RM550) (ICS 29.200 / 33.100)
MS IEC 61800-4 : 2009 - Adjustable speed electrical power drive
systems - Part 4 : General requirements - Rating specifications
for a.c power drive systems above 1000 V a.c and not exceeding 35
kV (RM550) (ICS 29.160.30 / 29.200)
MS IEC 61800-5-1 : 2009 - Adjustable speed electrical power drive
systems - Part 5-1 : Safety requirements - Electrical, thermal
and energy (RM550) (ICS 29.130)
MS IEC 61800-5-2 : 2009 - Adjustable speed electrical power drive
systems - Part 5-2 : Safety requirements - Functional (RM490)
(ICS 29.200 / 13.110)
MS IEC 61800-7-1 : 2009 - Adjustable speed electrical power drive
systems - Part 7-1 : Generic interface and use of profiles for
power drive systems - Interface definition (RM540) (ICS
29.200 / 35.100.05)
MS IEC 61800-7-201 : 2009 - Adjustable speed electrical power
drive systems - Part 7-201 : Generic interface and use of
profiles for power drive systems - Profiles type 1 specification
(RM570) (ICS 29.200 / 35.100.05)
MS IEC 61800-7-202 : 2009 - Adjustable speed electrical power
drive systems - Part 7-202 : Generic interface and use of
profiles for power drive systems - Profiles type 2 specification
(RM590) (ICS 29.200 / 35.100.05)
MS IEC 61800-7-204 : 2009 - Adjustable speed electrical power
drive systems - Part 7-204 : Generic interface and use of
profiles for power drive systems - Profiles type 4 specification
(RM640) (ICS 29.200 / 35.100.05)
MS IEC 61800-7-301 : 2009 - Adjustable speed electrical power
drive systems - Part 7-301 : Generic interface and use of
profiles for power drive systems - Mapping of profile type 1 to
network technologies (RM560) (ICS 29.200 / 35.100.05)
MS IEC 61800-7-302 : 2009 - Adjustable speed electrical power
drive systems - Part 7-302 : Generic interface and use of
profiles for power drive systems - Mapping of profile type 2 to
network technologies (RM270) (ICS 29.200 / 35.100.05)
MS IEC 62040-2 : 2009 - Uninterruptible power systems (UPS) -
Part 2 : Electromagnetic compatibility (EMC) requirements (First
revision) (RM330) (ICS 33.100.10 / 29.200 / 17.220)
MS IEC 62271-1 : 2009 -
High-voltage switchgear and controlgear - Part 1 : Common
specifications (First revision) (RM560) (ICS 29.130.10 /
29.130.99)
33. Telecommunications. Audio and Video Engineering
MS 301 489-1 : 2009 -
Electromagnetic compatibility and radio spectrum matter (ERM);
electromagnetic compatibility (EMC) standard for radio equipment
and services; Part 1 : Common technical requirements (RM40) (ICS
33.100)
MS 301 489-5 : 2009 - Electromagnetic compatibility and radio
spectrum matter (ERM); electromagnetic compatibility (EMC)
standard for radio equipment and services; Part 5 : Specific
conditions for private land mobile radio (PMR) and ancillary
equipment (speech and non-speech) (RM20) (ICS 33.100)
MS 301 489-6 : 2009 - Electromagnetic compatibility and radio
spectrum matter (ERM); electromagnetic compatibility (EMC)
standard for radio equipment and services; Part 6 : Specific
conditions for digital enhanced cordless telecommunications
(DECT) equipment (RM20) (ICS 33.100)
MS 301 489-7 : 2009 - Electromagnetic compatibility and radio
spectrum matter (ERM); electromagnetic compatibility (EMC)
standard for radio equipment and services; Part 7 : Specific
conditions for mobile and portable radio and ancillary equipment
of digital cellular radio telecommunications systems (GSM and
DCS) (RM30) (ICS 33.100)
MS 301 489-8 : 2009 - Electromagnetic compatibility and radio
spectrum matter (ERM); electromagnetic compatibility (EMC)
standard for radio equipment and services; Part 8 : Specific
conditions for GSM base stations (RM30) (ICS 33.100)
MS 301 489-9 : 2009 - Electromagnetic compatibility and radio
spectrum matter (ERM); electromagnetic compatibility (EMC)
standard for radio equipment and services; Part 9 : Specific
conditions for wireless microphones, similar radio frequency (RF)
audio link equipment, cordless audio and in-ear monitoring
devices (RM30) (ICS 33.100)
MS 301 489-17 : 2009 - Electromagnetic compatibility and radio
spectrum matter (ERM); electromagnetic compatibility (EMC)
standard for radio equipment; Part 17 : Specific conditions for
2.4 gHz wideband transmission systems, 5 gHz high performance
RLAN equipment and 5,8 gHz broadband data transmitting systems
(RM20) (ICS 33.100)
MS CISPR 12 : 2009 - Vehicles, boats and internal combustion
engines - Radio disturbance characteristics - Limits and methods
of measurement for the protection of off-board receivers (Second
revision) (RM480) (ICS 33.100.10 / 27.020)
MS CISPR 13 : 2009 - Sound and television broadcast receivers and
associated equipment - Radio disturbance characteristics - Limits
and methods of measurement (Second revision) (RM420) (ICS
33.100.10)
MS CISPR 14-1 : 2009 - Electromagnetic compatibility -
Requirements for household appliances, electric tools and similar
apparatus - Part 1 : Emission (Second revision) (RM490) (ICS
33.100.10)
MS CISPR 15 : 2009 - Limits and methods of measurement of radio
disturbance characteristics of electrical lighting and similar
equipment (Second revision) (RM480) (ICS 33.100.10)
MS CISPR 20 : 2009 - Sound and television broadcast receivers and
associated equipment - Immunity charateristics - Limits and
methods of measurement (Second revision) (RM520) (ICS
33.100.20)
MS CISPR 22 : 2009 - Information technology equipment - Radio
disturbance characteristics - Limits and methods of measurement
(Second revision) (RM520) (ICS 33.100.10)
MS IEC 61000-6-3 : 2009 - Electromagnetic compatibility (EMC) -
Part 6-3 : Generic standards - Emission standard for residential,
commercial and light-industrial environment (First revision)
(RM140) (ICS 33.100.10)
MS IEC 61000-6-4 : 2009 - Electromagnetic compatibility (EMC) -
Part 6-4 : Generic standards - Emission standard for industrial
environment (First revision) (RM120) (ICS 33.100.10)
MS IEC 61800-3 : 2009 - Adjustable speed electrical power drive
systems - Part 3 : EMC requirements and specific test methods
(First revision) (RM550) (ICS 29.200 / 33.100)
MS IEC 62040-2 : 2009 - Uninterruptible power systems (UPS) -
Part 2 : Electromagnetic compatibility (EMC) requirements (First
revision) (RM330) (ICS 33.100.10 / 29.200 / 17.220)
35. Information Technology. Office Machines
MS 2217 : 2009 -
Information technology - Biometrics tutorial (RM80) (ICS
35.040)
MS 62102 : 2008 - Electrical safety - Clasification of interfaces
for equipment to be connected to information and communications
technology network (RM30) (ICS 35.020 / 29.020)
MS IEC 61800-7-1 : 2009 -
Adjustable speed electrical power drive systems - Part 7-1 :
Generic interface and use of profiles for power drive systems -
Interface definition (RM540) (ICS 29.200 / 35.100.05)
MS IEC 61800-7-201 : 2009 - Adjustable speed electrical power
drive systems - Part 7-201 : Generic interface and use of
profiles for power drive systems - Profiles type 1 specification
(RM570) (ICS 29.200 / 35.100.05)
MS IEC 61800-7-202 : 2009 - Adjustable speed electrical power
drive systems - Part 7-202 : Generic interface and use of
profiles for power drive systems - Profiles type 2 specification
(RM590) (ICS 29.200 / 35.100.05)
MS IEC 61800-7-204 : 2009
- Adjustable speed electrical power drive systems - Part 7-204 :
Generic interface and use of profiles for power drive systems -
Profiles type 4 specification (RM640) (ICS 29.200 /
35.100.05)
MS IEC 61800-7-301 : 2009 - Adjustable speed electrical power
drive systems - Part 7-301 : Generic interface and use of
profiles for power drive systems - Mapping of profile type 1 to
network technologies (RM560) (ICS 29.200 / 35.100.05)
MS IEC 61800-7-302 : 2009 - Adjustable speed electrical power
drive systems - Part 7-302 : Generic interface and use of
profiles for power drive systems - Mapping of profile type 2 to
network technologies (RM270) (ICS 29.200 / 35.100.05)
MS ISO 17115 : 2009 - Health informatics - Vocabulary for
terminological systems (RM160) (ICS 01.040.35 / 35.240.80)
MS ISO/IEC 18028-2 : 2008 - Information technology - Security
techniques - IT network security - Part 2 : Network security
architecture (RM230) (ICS 35.040)
MS ISO/IEC 27005- : 2008 - Information technology - Security
techniques - Information security risk management (RM70) (ICS
35.040)
43. Road Vehicle Engineering
MS 1025 : 2008 - Wheel
rims for motorcycle and assembly - Specification (First revision)
(RM20) (ICS 43.140)
MS ISO 4929 : 2009 - Road vehicles - Diaphragm gaskets for
hydraulic brake master cylinder reservoirs using non-petroleum
base hydraulic brake fluid (RM100) (ICS 43.040.40)
MS ISO 8092-3 : 2009 -
Road vehicles - Connections for on-board electrical wiring
harnesses - Part 3 : Tabs for multi-pole connections - Dimensions
and specific requirements (RM100) (ICS 43.040.10)
MS ISO 8092-4 : 2009 - Road vehicles - Connections for on-board
electrical wiring harnesses - Part 4 : Pins for single and
multi-pole connections - Dimensions and specific requirements
(RM100) (ICS 43.040.10)
MS ISO 8854 : 2009 - Road vehicles - Alternators with regulators
- Test methods and general requirements (First revision) (RM10) (ICS
43.060.50)
MS ISO 12161 : 2009 - Road vehicles - Endurance braking systems
of motor vehicles and towed vehicles - Test procedures (RM240) (ICS
43.040.40)
MS ISO 13476 : 2009 - Road vehicles - Ignition coils - Electrical
characteristics and test methods (RM140) (ICS 43.060.50)
MS ISO 22628 : 2009 - Road vehicles - Recyclability and
recoverability - Calculation method (RM130) (ICS 43.020)
53. Materials Handling Equipment
MS 2204 : 2008 - Cranes -
Equipment for lifting persons - Part 1 : Suspended baskets (RM30)
(ICS 53.020.30)
55. Packaging and Distribution of Goods
MS ISO 668 : 2009 -
Series 1 freight containers - Classification, dimensions and
rating (First revision) (RM30) (ICS 55.180.10)
MS ISO 1496-1 : 2009 - Series 1 freight containers -
Specification and testing - Part 1 : General cargo containers for
general purposes (First revision) (RM40) (ICS 55.180.10)
MS ISO 1496-3 : 2009 - Series 1 freight containers -
Specification and testing - Part 3 : Tank containers for liquids,
gases and pressurised dry bulk (First revision) (RM50) (ICS
55.180.10)
59. Textile and Leather
Technology
MS ISO 3759 : 2009 -
Textiles - Preparation, marking and measuring of fabric specimens
and garments in tests for determination of dimensional change
(First revision) (RM110) (ICS 59.080.30 / 61.020)
61. Clothing Industry
MS ISO 3759 : 2009 -
Textiles - Preparation, marking and measuring of fabric specimens
and garments in tests for determination of dimensional change
(First revision) (RM110) (ICS 59.080.30 / 61.020)
MS ISO 4417 : 2009 - Size
designation of clothes - Headwear (RM80) (ICS 61.040 /
61.020)
65. Agriculture
MS ISO 13906 : 2009 -
Animal feeding stuffs - Determination of acid detergent fibre
(ADF) and acid detergent lignin (ADL) contents (RM200) (ICS
65.120)
MS ISO 17372 : 2009 - Animal feeding stuffs - Determination of
zearalenone by immunoaffinity column chromatography and high
performance liquid chromatography (RM180) (ICS 65.120)
67. Food Technology
MS 513 : 2009 - Caramel
in the manufacture of soy sauce - Specification (Second revision)
(RM30) (ICS 67.220.20)
MS 1118 : 2008 - Malaysian cocoa butter - Specification (First
revision) (RM10) (ICS 67.140.30)
MS 1376 : 2008 - Malaysian cocoa mass - Specification (First
revision) (RM10) (ICS 67.140.30)
MS 2229 : 2009 - Milk powder - Determination of soy and pea
proteins using capillary electrophoresis in the presence of
sodium dodecyl sulfate (SDS-CE) - Screening method (RM20) (ICS
67.100.01)
MS ISO 663 : 2009 - Animal and vegetable fats and oils -
Determination of insoluble impurities content (RM110) (ICS
67.200.10)
MS ISO 3657 : 2009 - Animal and vegetable fats and oils -
Determination of saponification value (RM110) (ICS 67.200.10)
MS ISO 3960 : 2009 - Animal and vegetable fats and oils -
Determination of peroxide value - Iodometric (visual) endpoint
determination (RM140) (ICS 67.200.10)
MS ISO 6883 : 2009 - Animal and vegetable fats and oils -
Determination of conventional mass per volume (litre weight in
air) (RM140) (ICS 67.200.10)
71. Chemical Technology
MS IEC 61010-2-081 : 2008
- Safety requirements for electrical equipment for measurement,
control and laboratory use - Part 2-081 : Particular requirements
for automatic and semi-automatic laboratory equipment for
analysis and other purposes (RM200) (ICS 19.080 / 71.040.20)
MS ISO 855 : 2009 - Oil of lemon [Citrus
limon (L.) Burm. f.], obtained by
expression (RM140) (ICS 71.100.60)
MS ISO 3044 : 2009 - Oil of Eucalyptus
citriodora Hook. (RM110) (ICS
71.100.60)
MS ISO 3061 : 2009 - Oil of black pepper (Piper nigrum
L.) (RM140) (ICS 71.100.60)
MS ISO 3063 : 2009 - Oil of ylang-ylang [cananga
odorata (Lam.) Hook. f. et Thomson forma genuina]
(RM160) (ICS 71.100.60)
MS ISO 3215 : 2009 - Oil
of nutmeg, Indonesian type (Myristica frangrans
Houtt.) (RM110) (ICS 71.100.60)
MS ISO 4715 : 2009 - Essential oils - Quantitative evaluation of
residue on evaporation (RM80) (ICS 71.100.60)
MS ISO 4735 : 2009 - Oils of Citrus -
Determination of CD value by ultraviolet spectrometric analysis
(RM110) (ICS 71.100.60)
MS ISO 5771 : 2009 - Rubber hoses and hose assemblies for
transferring anhydrous ammonia - Specification (RM20) (ICS
71.120.99 / 83.140.40)
MS ISO 7358 : 2009 - Oils of Bergamot, Lemon, Citron and Lime,
fully or partially reduced in bergapten - Determination of
bergapten content by high-pressure liquid chromatography (HPLC)
(RM110) (ICS 71.100.60)
MS ISO 7359 : 2009 - Essential oils - Analysis by gas
chromatography on packed columns - General method (RM130)
(ICS 71.100.60)
MS ISO 7609 : 2009 - Essential oils - Analysis by gas
chromatography on capillary columns - General method (RM130) (ICS
71.100.60)
MS ISO 9301 : 2009 - Oil of Cumin seed (Cuminum
cyminum L.) (RM130) (ICS 71.100.60)
MS ISO 17494 : 2009 - Aromatic extracts, flavouring and perfuming
compounds - Determination of ethanol content - Gas chromatography
method on packed and capillary columns (RM140) (ICS
71.100.60)
MS ISO 22972 : 2009 - Essential oils - Analysis by gas
chromatography on chiral capillary columns - General method
(RM100) (ICS 71.100.60)
75. Petroleum and Related Technologies
MS 133 : Part A10 : 2008 - Paints, varnishes - Determination of
flash point - Part A10 : Close cup equilibrium method (Second
revision) (RM20) (ICS 87.040 / 75.080)
MS ISO 3183 : 2009 -
Petroleum and natural gas industries - Steel pipe for pipeline
transportation systems (First revision) (RM470) (ICS
75.200 / 77.140.75)
MS ISO 18453 : 2008 - Natural gas - Correlation
between water content and water dew point (RM230) (ICS
75.060)
MS ISO 19739 : 2008 - Natural gas - Determination of sulfur
compounds using gas chromatography (First revision) (RM340) (ICS
75.060)
77. Metallurgy
MS 1239-1 :
2009 - Zinc or zinc alloy coated non-alloy steel wire for
armouring either power cables or telecommunication cables - Part
1 : Land cables (First revision) (RM10) (ICS 77.140.70)
MS 1463 : 2008 - Grey cast irons - Classification (First
revision) (RM30) (ICS 77.080.10)
MS 2212 : 2009 - Practice for production and evaluation of field
metallographic replicas (RM40) (ICS 77.040.10)
MS 2213 : 2009
- Guide for preparation of metallographic specimens (RM60) (ICS
77.040.10)
MS ISO 148-1 : 2008 - Metallic materials - Charpy pendulum impact
test - Part 1 : Test method (RM210) (ICS 77.040.10)
MS ISO 148-2 : 2008 - Metallic materials - Charpy pendulum impact
test - Part 2 : Verification of test machines (RM180) (ICS
77.040.10)
MS ISO 148-3 : 2008 - Metallic materials - Charpy pendulum impact
test - Part 3 : Preparation and characterization of charpy V
reference test pieces for verification of test machines (RM140)
(ICS 77.040.10)
MS ISO 3183 : 2009 - Petroleum and natural gas industries - Steel
pipe for pipeline transportation systems (First revision) (RM470)
(ICS 75.200 / 77.140.75)
MS ISO 4545-1 : 2009 - Metallic materials - Knoop hardness test -
Part 1 : Test method (First revision) (RM170) (ICS
77.040.10)
MS ISO 4545-2 : 2009 - Metallic materials - Knoop hardness test -
Part 2 : Verification and calibration of testing machines (First
revision) (RM170) (ICS 77.040.10)
MS ISO 4545-3 : 2009 - Metallic materials - Knoop hardness test -
Part 3 : Calibration of reference blocks (First revision) (RM140)
(ICS 77.040.10)
MS ISO 4545-4 : 2009 - Metallic materials - Knoop hardness test -
Part 4 : Table of hardness values (RM230) (ICS
77.040.10)
MS ISO 6506-4 :
2009 - Metallic materials - Brinell hardness test - Part 4 :
Table of hardness values (RM160) (ICS 77.040.10)
MS ISO 15630-3 : 2009 - Steel for the reinforcement and
prestressing of concrete - Test methods - Part 3 : Prestressing
steel (RM230) (ICS 77.140.15)
83. Rubber and Plastics Industries
MS ISO 37 : 2009 - Rubber, vulcanized or thermoplastic -
Determination of tensile stress-strain properties (First
revision) (RM30) (ICS 83.060)
MS ISO 48 : 2009 - Rubber, vulcanized or thermoplastic -
Determination of hardness (hardness between 10 irhd and 100 irhd
(First revision) (RM30) (ICS 83.060)
MS ISO 188 : 2008 - Rubber, vulcanized or thermoplastic -
Accelerated ageing and heat resistance tests (First revision)
(RM200) (ICS 83.060)
MS ISO 291 : 2008 - Plastics - Standard atmospheres for
conditioning and testing (First revision) (RM20) (ICS
83.080.01)
MS ISO 1431-1 : 2008 - Rubber, vulcanized or thermoplastic -
Resistance to ozone cracking - Part 1 : Static and dynamic strain
testing (First revision) (RM170) (ICS 83.060)
MS ISO 1827 : 2008 - Rubber, vulcanized or thermoplastic -
Determination of shear modulus and adhesion to rigid plates -
Quadruple-shear methods (First revision) (RM130) (ICS
83.060)
MS ISO 5603 : 2008 - Rubber, vulcanized - Determination
of adhesion to wire cord (First revision) (RM170) (ICS
83.060)
MS ISO 5771 : 2009 - Rubber hoses and hose assemblies for
transferring anhydrous ammonia - Specification (RM20) (ICS
71.120.99 / 83.140.40)
87. Paint and Colour
Industries
MS 133 : Part
A1 : 2008 - Paints, varnishes and raw materials for paints and
varnishes - Part A1 : Sampling (Second revision) (RM20) (ICS
87.040)
MS 133 : Part A2 : 2008 - Paints, varnishes - Part A2 :
Examination and preparation of samples for testing (Second
revision) (RM10) (ICS 87.040)
MS 133 : Part A3 : 2008 - Paints, varnishes - Part A3 : Standard
panels for testing (Second revision) (RM30) (ICS 87.040)
MS 133 : Part A10 : 2008 - Paints, varnishes - Determination of
flash point - Part A10 : Close cup equilibrium method (Second
revision) (RM20) (ICS 87.040 / 75.080)
MS 133 : Part A12 : 2008 - Paints, varnishes - Determination of
density - Part A12 : Pyknometer method (Second revision) (RM20) (ICS
87.040)
93. Civil
Engineering
MS 825 : Part 2
: 2008 - Code of practice for the design of road lighting - Part
2 : Lighting of tunnels (RM40) (ICS 93.080.40)